| PDF Pages<\/th>\n | PDF Title<\/th>\n<\/tr>\n | ||||||
|---|---|---|---|---|---|---|---|
| 4<\/td>\n | Foreword <\/td>\n<\/tr>\n | ||||||
| 7<\/td>\n | Foreword <\/td>\n<\/tr>\n | ||||||
| 8<\/td>\n | Introduction <\/td>\n<\/tr>\n | ||||||
| 9<\/td>\n | 1\tScope 2\tNormative references 3\tTerms and definitions <\/td>\n<\/tr>\n | ||||||
| 10<\/td>\n | 4\tSymbols and designations <\/td>\n<\/tr>\n | ||||||
| 11<\/td>\n | 5\tPrinciple 6\tTest piece 7\tDetermination of original cross-sectional area (So) 8\tMarking the original gauge length (Lo) 9\tApparatus 9.1\tForce measuring system 9.2\tExtensometer 9.3\tCooling device 9.3.1\tGeneral <\/td>\n<\/tr>\n | ||||||
| 12<\/td>\n | 9.3.2\tPermitted deviations of temperature 9.3.3\tMeasurement of temperature <\/td>\n<\/tr>\n | ||||||
| 13<\/td>\n | 9.3.4\tVerification of the temperature-measuring system 10\tTest conditions 10.1\tSetting the force zero point 10.2\tGripping of the test piece, fixing of the extensometer and cooling of the test piece, not necessarily in the following sequence 10.2.1\tMethod of gripping 10.2.2\tFixing of the extensometer and establishing the gauge length <\/td>\n<\/tr>\n | ||||||
| 14<\/td>\n | 10.2.3\tCooling of the test piece 10.3\tTesting rate based on strain rate control (Method A) 10.3.1\tGeneral 10.3.2\tStrain rate for the determination of the upper yield strength (ReH) or proof strength properties (Rp and, if required, Rt) <\/td>\n<\/tr>\n | ||||||
| 15<\/td>\n | 10.3.3\tStrain rate for the determination of the lower yield strength (ReL) and percentage yield point extension (Ae) if required 10.3.4\tStrain rate for the determination of the tensile strength (Rm), percentage elongation after fracture (A), percentage reduction area (Z), and, if required, percentage total extension at the maximum force (Agt), percentage plastic extension at maximu 10.4\tMethod of testing with expanded strain rate ranges (Method B) 10.4.1\tGeneral 10.4.2\tRate for the determination of yield strength or proof strength properties <\/td>\n<\/tr>\n | ||||||
| 16<\/td>\n | 10.4.3\tRate for the determination of tensile strength 10.5\tChoice of the method and rates 10.6\tDocumentation of the chosen testing conditions 11\tDetermination or calculation of the properties 12\tTest report <\/td>\n<\/tr>\n | ||||||
| 17<\/td>\n | 13\tMeasurement uncertainty <\/td>\n<\/tr>\n | ||||||
| 18<\/td>\n | 14\tFigures <\/td>\n<\/tr>\n | ||||||
| 19<\/td>\n | 15\tAnnexes <\/td>\n<\/tr>\n | ||||||
| 20<\/td>\n | Annex\u00a0A (informative) Addition to ISO\u00a06892-1:2009, Annexes\u00a0B and D <\/td>\n<\/tr>\n | ||||||
| 25<\/td>\n | Annex\u00a0B (informative) Example for cooling curves of steel depending on test piece dimensions and the specified test temperature in ethanol and liquid nitrogen <\/td>\n<\/tr>\n | ||||||
| 29<\/td>\n | Annex\u00a0C (informative) Measurement uncertainty <\/td>\n<\/tr>\n | ||||||
| 30<\/td>\n | Bibliography <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":" Metallic materials. Tensile testing – Method of test at low temperature<\/b><\/p>\n |