This European Standard gives requirements and the corresponding test\/assessment methods applicable to leak detection kits based on the detection of the presence of liquid and\/or vapour in interstitial spaces, leakage containments or monitoring wells. The kits are usually composed by: – sensing device(s); – evaluation device; – alarm device.<\/p>\n
| PDF Pages<\/th>\n | PDF Title<\/th>\n<\/tr>\n | ||||||
|---|---|---|---|---|---|---|---|
| 61<\/td>\n | Contents <\/td>\n<\/tr>\n | ||||||
| 65<\/td>\n | 1 Scope 2 Normative references 3 Terms and definitions 4 Requirements 4.1 Effectiveness 4.1.1 General <\/td>\n<\/tr>\n | ||||||
| 66<\/td>\n | 4.1.2 Presence of liquids 4.1.3 Presence of vapours 4.1.4 Re-usability of the sensor 4.1.5 Requirements for software, (only if provided) <\/td>\n<\/tr>\n | ||||||
| 67<\/td>\n | 4.2 Durability of effectiveness 4.2.1 Durability of effectiveness against temperature 4.2.2 Durability of effectiveness against chemical attack 5 Testing, assessment and sampling methods 5.1 Effectiveness of the leak detection systems 5.1.1 General 5.1.2 Presence of liquid 5.1.2.1 Non-discriminating liquid sensors (Category 1) <\/td>\n<\/tr>\n | ||||||
| 69<\/td>\n | 5.1.2.2 Discriminating liquid sensors of Category 2A <\/td>\n<\/tr>\n | ||||||
| 70<\/td>\n | 5.1.2.3 Discriminating liquid sensors of category 2B <\/td>\n<\/tr>\n | ||||||
| 71<\/td>\n | 5.1.3 Presence of vapours 5.1.3.1 General 5.1.3.2 Evaluation 5.1.4 Re-usability of the discriminating and non-discriminating sensors 5.1.4.1 Test equipment <\/td>\n<\/tr>\n | ||||||
| 72<\/td>\n | 5.1.4.2 Preparation 5.1.4.3 Procedure 5.1.4.4 Evaluation 5.1.5 Re-usability of vapour sensors 5.1.5.1 General 5.1.5.2 Evaluation 5.1.6 Software (only if provided) 5.1.6.1 Test equipment 5.1.6.2 Preparation <\/td>\n<\/tr>\n | ||||||
| 73<\/td>\n | 5.1.6.3 Test method 5.1.6.4 Evaluation 5.2 Durability of effectiveness 5.2.1 Durability of effectiveness against temperature 5.2.1.1 Test equipment <\/td>\n<\/tr>\n | ||||||
| 74<\/td>\n | 5.2.1.2 Preparation 5.2.1.3 Test method <\/td>\n<\/tr>\n | ||||||
| 75<\/td>\n | 5.2.1.4 Evaluation 5.2.2 Durability of effectiveness against chemical attack 5.2.2.1 Test equipment <\/td>\n<\/tr>\n | ||||||
| 76<\/td>\n | 5.2.2.2 Preparation 5.2.2.3 Test method 5.2.2.4 Evaluation 6 Assessment and verification of constancy of performance – AVCP 6.1 General 6.2 Type testing 6.2.1 General <\/td>\n<\/tr>\n | ||||||
| 77<\/td>\n | 6.2.2 Test samples, testing and compliance criteria <\/td>\n<\/tr>\n | ||||||
| 78<\/td>\n | 6.2.3 Test reports 6.2.4 Shared other party results <\/td>\n<\/tr>\n | ||||||
| 79<\/td>\n | 6.2.5 Cascading determination of the product type results <\/td>\n<\/tr>\n | ||||||
| 80<\/td>\n | 6.3 Factory production control (FPC) 6.3.1 General 6.3.2 Requirements 6.3.2.1 General <\/td>\n<\/tr>\n | ||||||
| 81<\/td>\n | 6.3.2.2 Equipment 6.3.2.3 Raw materials and components <\/td>\n<\/tr>\n | ||||||
| 82<\/td>\n | 6.3.2.4 Traceability and marking 6.3.2.5 Controls during manufacturing process 6.3.2.6 Product testing and evaluation 6.3.2.7 Non-complying products 6.3.2.8 Corrective action 6.3.2.9 Handling, storage and packaging <\/td>\n<\/tr>\n | ||||||
| 83<\/td>\n | 6.3.3 Product specific requirements 6.3.4 Procedure for modifications 6.3.5 One-off products, pre-production products (e.g. prototypes) and products produced in very low quantity <\/td>\n<\/tr>\n | ||||||
| 84<\/td>\n | 7 Marking, labelling and packaging <\/td>\n<\/tr>\n | ||||||
| 85<\/td>\n | 8 Environmental aspects <\/td>\n<\/tr>\n | ||||||
| 86<\/td>\n | Annex\u00a0A (informative)Environmental aspects <\/td>\n<\/tr>\n | ||||||
| 88<\/td>\n | Annex\u00a0ZA (informative)Clauses of this European Standard addressing the provisions of the EU Construction Products Regulation <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":" Tracked Changes. Leak detection systems – Requirements and test\/assessment methods for sensor based leak detection systems<\/b><\/p>\n |