{"id":252143,"date":"2024-10-19T16:38:33","date_gmt":"2024-10-19T16:38:33","guid":{"rendered":"https:\/\/pdfstandards.shop\/product\/uncategorized\/bs-en-62271-2062011\/"},"modified":"2024-10-25T11:57:15","modified_gmt":"2024-10-25T11:57:15","slug":"bs-en-62271-2062011","status":"publish","type":"product","link":"https:\/\/pdfstandards.shop\/product\/publishers\/bsi\/bs-en-62271-2062011\/","title":{"rendered":"BS EN 62271-206:2011"},"content":{"rendered":"
This part of IEC 62271 is applicable to voltage presence indicating systems (VPIS) incorporated in a.c. switchgear and controlgear covered by IEC 62271-200 or IEC 62271-201.<\/p>\n
Voltage presence indicating systems are devices used to provide information to operators about the voltage condition of the main circuit of the switchgear in which they are installed.<\/p>\n
The indication of VPIS alone is not sufficient to prove that the system is dead: if operating procedures make it mandatory, relevant voltage detectors according to IEC 61243-1, IEC 61243-2 and IEC 61243-5 should be used.<\/p>\n
This standard is also applicable to phase comparators specifically designed for use with VPIS.<\/p>\n
PDF Pages<\/th>\n | PDF Title<\/th>\n<\/tr>\n | ||||||
---|---|---|---|---|---|---|---|
6<\/td>\n | English \n CONTENTS <\/td>\n<\/tr>\n | ||||||
9<\/td>\n | 1 General 1.1 Scope 1.2 Normative references 2 Service conditions <\/td>\n<\/tr>\n | ||||||
10<\/td>\n | 3 Terms and definitions 4 Ratings <\/td>\n<\/tr>\n | ||||||
11<\/td>\n | 4.1 Rated voltage 4.2 Rated insulation level 4.3 Rated frequency 5 Design and construction 5.1 General 5.2 Threshold values for voltage presence indication <\/td>\n<\/tr>\n | ||||||
12<\/td>\n | 5.3 Indication and perceptibility 5.4 Coupling element and voltage limiting device Tables \n Table 1 \u2013 Indication corresponding to “voltage present” <\/td>\n<\/tr>\n | ||||||
13<\/td>\n | 5.5 Marking 5.6 Phase comparator and connecting point <\/td>\n<\/tr>\n | ||||||
14<\/td>\n | 5.7 Electromagnetic compatibility (EMC) <\/td>\n<\/tr>\n | ||||||
15<\/td>\n | 6 Type tests 6.1 General <\/td>\n<\/tr>\n | ||||||
16<\/td>\n | 6.2 Arrangement, assembly, marking, and instructions for use 6.3 Clear indication of VPIS 6.4 Response time of VPIS <\/td>\n<\/tr>\n | ||||||
17<\/td>\n | 6.5 Dielectric strength of the coupling element of VPIS 6.6 Maximum current delivered by the connecting point 6.7 Voltage limiting device <\/td>\n<\/tr>\n | ||||||
18<\/td>\n | 6.8 Clear perceptibility of visual indication <\/td>\n<\/tr>\n | ||||||
19<\/td>\n | 6.9 Impact resistance 6.10 Clear indication of phase comparators <\/td>\n<\/tr>\n | ||||||
20<\/td>\n | 6.11 Electromagnetic compatibility tests (EMC) 6.12 Indication until power source is exhausted <\/td>\n<\/tr>\n | ||||||
21<\/td>\n | 7 Routine tests 7.1 General 7.2 Clear indication 8 Guide to the selection of VPIS 9 Information to be given with enquiries, tenders and orders 10 Instructions for use 10.1 General 10.2 Instructions for use of VPIS <\/td>\n<\/tr>\n | ||||||
22<\/td>\n | 10.3 Instructions for use of phase comparators 11 Safety <\/td>\n<\/tr>\n | ||||||
23<\/td>\n | Figures \n Figure 1 \u2013 Voltage presence indicating system Table 2 \u2013 Sequence of type tests for VPIS and phase comparators (PC) <\/td>\n<\/tr>\n | ||||||
24<\/td>\n | Figure 2 \u2013 Examples for measuring the response time <\/td>\n<\/tr>\n | ||||||
25<\/td>\n | Figure 3 \u2013 Test set-up for perceptibility of visual indication <\/td>\n<\/tr>\n | ||||||
26<\/td>\n | Bibliography <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":" High-voltage switchgear and controlgear – Voltage presence indicating systems for rated voltages above 1 kV and up to and including 52 kVkV and up to and including 52 kV<\/b><\/p>\n |