| PDF Pages<\/th>\n | PDF Title<\/th>\n<\/tr>\n | ||||||
|---|---|---|---|---|---|---|---|
| 2<\/td>\n | undefined <\/td>\n<\/tr>\n | ||||||
| 4<\/td>\n | CONTENTS <\/td>\n<\/tr>\n | ||||||
| 7<\/td>\n | FOREWORD <\/td>\n<\/tr>\n | ||||||
| 9<\/td>\n | 0 Introduction to the template provided by this blank detail specification 0.1 Scope of this blank detail specification 0.2 Function of this blank detail specification <\/td>\n<\/tr>\n | ||||||
| 10<\/td>\n | 0.3 Identification of the detail specification and the resistor <\/td>\n<\/tr>\n | ||||||
| 12<\/td>\n | 1 Scope 2 Normative references <\/td>\n<\/tr>\n | ||||||
| 13<\/td>\n | 3 Terms and definitions 4 Characteristics and ratings 4.1 General 4.2 Dimensions <\/td>\n<\/tr>\n | ||||||
| 14<\/td>\n | Figures Figure 1 \u2013 Outline and dimensions Tables Table 1 \u2013 Styles and dimensions <\/td>\n<\/tr>\n | ||||||
| 15<\/td>\n | 4.3 Ratings Figure 2 \u2013 Lead eccentricity of the wire terminations Figure 3 \u2013 Length of excessive coating on the wire terminations <\/td>\n<\/tr>\n | ||||||
| 16<\/td>\n | Table 2 \u2013 Climatic categories Table 3 \u2013 Ratings <\/td>\n<\/tr>\n | ||||||
| 17<\/td>\n | 4.4 Resistance range and tolerance on resistance Figure 4 \u2013 Derating curve for power resistors <\/td>\n<\/tr>\n | ||||||
| 18<\/td>\n | 5 Tests and test severities 5.1 General 5.2 Resistance Table 4 \u2013 Temperature coefficients, tolerances and resistance rangesfor climatic category … \/ … \/ … <\/td>\n<\/tr>\n | ||||||
| 19<\/td>\n | 5.3 Temperature coefficient of resistance 5.4 Temperature rise 5.5 Endurance at the rated temperature 70 \u00b0C 5.6 Endurance at other than rated temperature 5.6.1 Endurance at room temperature 5.6.2 Endurance at a maximum temperature: UCT with category dissipation 5.7 Short-term overload of power resistors 5.7.1 Power film resistors <\/td>\n<\/tr>\n | ||||||
| 20<\/td>\n | 5.7.2 Wirewound resistors 5.8 Electrostatic discharge (ESD) test 5.9 Visual examination Table 5 \u2013 Short-term overload duration Table 6 \u2013 ESD test voltages <\/td>\n<\/tr>\n | ||||||
| 21<\/td>\n | 5.10 Gauging of dimensions 5.11 Detail dimensions 5.12 Robustness 5.12.1 Robustness of terminations 5.12.2 Robustness of the resistor body 5.13 Shock and vibration 5.13.1 Vibration 5.13.2 Shock or bump 5.14 Rapid change of temperature <\/td>\n<\/tr>\n | ||||||
| 22<\/td>\n | 5.15 Climatic sequence 5.16 Damp heat, steady state test Table 7 \u2013 Additional cycles of the damp heat, cyclic test Table 8 \u2013 Damp heat, steady state test duration <\/td>\n<\/tr>\n | ||||||
| 23<\/td>\n | 5.17 Solderability, with lead-free solder 5.18 Solderability, with SnPb solder 5.19 Resistance to soldering heat 5.20 Solvent resistance test <\/td>\n<\/tr>\n | ||||||
| 24<\/td>\n | 5.21 Insulation resistance 5.22 Voltage proof 5.23 Flammability test 6 Performance requirements 6.1 General 6.2 Limits for change of resistance at tests <\/td>\n<\/tr>\n | ||||||
| 25<\/td>\n | 6.3 Temperature coefficient of resistance Table 9 \u2013 Limits for change of resistance at tests <\/td>\n<\/tr>\n | ||||||
| 26<\/td>\n | 6.4 Temperature rise 6.5 Visual examination 6.5.1 General visual criteria Table 10 \u2013 Permitted change of resistance due to the variation of temperature <\/td>\n<\/tr>\n | ||||||
| 27<\/td>\n | 6.5.2 Visual criteria after tests 6.5.3 Visual criteria for packaging 6.6 Solderability 6.7 Insulation resistance <\/td>\n<\/tr>\n | ||||||
| 28<\/td>\n | 6.8 Flammability 7 Marking, packaging and ordering information 7.1 Marking of the component 7.2 Packaging 7.3 Marking of the packaging 7.4 Ordering information <\/td>\n<\/tr>\n | ||||||
| 29<\/td>\n | 8 Additional information 8.1 General 8.2 Storage and Transportation 8.3 Substrate for assembly 8.4 Soldering process 8.5 Use of cleaning agents or solvents <\/td>\n<\/tr>\n | ||||||
| 30<\/td>\n | 8.6 Coating or potting after assembly 9 Quality assessment procedures 9.1 General 9.1.1 100 % test 9.1.2 Certificate of Conformity (CoC) <\/td>\n<\/tr>\n | ||||||
| 31<\/td>\n | 9.1.3 Certified test records of released lots 9.2 Qualification approval 9.3 Maintenance of a qualification approval 9.3.1 Quality conformance inspection 9.3.2 Non-conforming specimen <\/td>\n<\/tr>\n | ||||||
| 32<\/td>\n | Table 11 \u2013 Test schedule for the qualification approval of power resistors(1 of 5) <\/td>\n<\/tr>\n | ||||||
| 37<\/td>\n | Table 12 \u2013 Test schedule for quality conformance inspection of power resistors(1 of 5) <\/td>\n<\/tr>\n | ||||||
| 43<\/td>\n | Annex A (normative)Symbols and abbreviated terms A.1 Symbols <\/td>\n<\/tr>\n | ||||||
| 45<\/td>\n | A.2 Abbreviated terms <\/td>\n<\/tr>\n | ||||||
| 46<\/td>\n | Annex B (normative)Reference for visual examination <\/td>\n<\/tr>\n | ||||||
| 47<\/td>\n | Annex X (informative)Cross-reference for references to the prior revision of this specification Table X.1 \u2013 Cross reference for references to clauses <\/td>\n<\/tr>\n | ||||||
| 48<\/td>\n | Bibliography <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":" Fixed resistors for use in electronic equipment – Blank detail specification: Power resistors with axial leads for through-hole assembly on circuit boards (THT), for general electronic equipment, classification level G<\/b><\/p>\n |