This part of ISO 10360 specifies procedures for testing the performance of coordinate measuring machines of various designs that use multiple probing systems in contacting and non-contacting mode. It applies to<\/p>\n
acceptance tests for verifying the performance of a CMM and its probes as stated by the manufacturer,<\/p>\n<\/li>\n
reverification tests performed by the user for periodical checking of the CMM and its probes,<\/p>\n<\/li>\n
interim checks performed by the user for monitoring the CMM and its probes in between reverification tests.<\/p>\n<\/li>\n<\/ul>\n
It considers CMMs of single ram designs as well as multiple ram designs with small or with large overlapping measuring volume. It applies to multiple probing systems consisting of different types of probes (such as an imaging probe combined with a contacting probe, or two contacting probes of different individual performance).<\/p>\n
The tests described are sensitive to many errors attributable to both the CMM and the probing systems; they supplement the length measurement tests and the individual probing error tests of each probing system. The length measurement tests, as well as the individual probing error tests (for example, ISO 10360-5, ISO 10360-7, or ISO 10360-8), should be performed before executing the procedures in this part of ISO 10360.<\/p>\n
| PDF Pages<\/th>\n | PDF Title<\/th>\n<\/tr>\n | ||||||
|---|---|---|---|---|---|---|---|
| 4<\/td>\n | Foreword <\/td>\n<\/tr>\n | ||||||
| 6<\/td>\n | Foreword <\/td>\n<\/tr>\n | ||||||
| 7<\/td>\n | Introduction <\/td>\n<\/tr>\n | ||||||
| 9<\/td>\n | Section sec_1 Section sec_2 1\tScope 2\tNormative references <\/td>\n<\/tr>\n | ||||||
| 10<\/td>\n | Section sec_3 Section sec_3.1 Section sec_3.2 Section sec_3.3 Section sec_3.4 Section sec_3.5 3\tTerms and definitions <\/td>\n<\/tr>\n | ||||||
| 11<\/td>\n | Section sec_3.6 Section sec_3.7 Section sec_3.8 Section sec_3.9 Section sec_3.10 <\/td>\n<\/tr>\n | ||||||
| 12<\/td>\n | Section sec_3.11 Section sec_3.12 <\/td>\n<\/tr>\n | ||||||
| 13<\/td>\n | Section sec_4 Table tab_1 Section sec_5 Section sec_5.1 Section sec_5.2 4\tSymbols 5\tRequirements 5.1\tMultiple probing system errors 5.2\tEnvironmental conditions <\/td>\n<\/tr>\n | ||||||
| 14<\/td>\n | Section sec_5.3 Section sec_6 Section sec_6.1 Section sec_6.2 Section sec_6.3 5.3\tOperating conditions 6\tTesting 6.1\tGeneral 6.2\tPrinciple 6.3\tMeasuring equipment <\/td>\n<\/tr>\n | ||||||
| 16<\/td>\n | Figure fig_1 <\/td>\n<\/tr>\n | ||||||
| 17<\/td>\n | Table tab_d Figure fig_1___1 Section sec_6.4 6.4\tProcedure <\/td>\n<\/tr>\n | ||||||
| 18<\/td>\n | Section sec_6.5 6.5\tData analysis <\/td>\n<\/tr>\n | ||||||
| 19<\/td>\n | Section sec_7 Section sec_7.1 Section sec_7.2 Section sec_8 Section sec_8.1 7\tCompliance with specifications 7.1\tAcceptance tests 7.2\tReverification tests 8\tApplications 8.1\tAcceptance tests <\/td>\n<\/tr>\n | ||||||
| 20<\/td>\n | Section sec_8.2 Section sec_8.3 Section sec_9 Table tab_2 8.2\tReverification tests 8.3\tInterim checks 9\tIndication in product documentation and data sheets <\/td>\n<\/tr>\n | ||||||
| 21<\/td>\n | Annex sec_A Table tab_A.1 Annex\u00a0A \n(informative)<\/p>\n Example of specification sheet <\/td>\n<\/tr>\n | ||||||
| 23<\/td>\n | Table tab_A.2 <\/td>\n<\/tr>\n | ||||||
| 24<\/td>\n | Annex sec_B Annex sec_B.1 Annex sec_B.2 Annex sec_B.3 Table tab_B.1 Annex\u00a0B \n(informative)<\/p>\n Relation to the GPS matrix model <\/td>\n<\/tr>\n | ||||||
| 25<\/td>\n | Annex sec_B.4 <\/td>\n<\/tr>\n | ||||||
| 26<\/td>\n | Reference ref_1 Reference ref_2 Reference ref_3 Reference ref_4 Reference ref_5 Reference ref_6 Reference ref_7 Bibliography <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":" Geometrical product specifications (GPS). Acceptance and reverification tests for coordinate measuring systems (CMS) – CMMs with multiple probing systems<\/b><\/p>\n |