{"id":230468,"date":"2024-10-19T14:59:46","date_gmt":"2024-10-19T14:59:46","guid":{"rendered":"https:\/\/pdfstandards.shop\/product\/uncategorized\/bs-en-60939-22005-2006\/"},"modified":"2024-10-25T09:14:41","modified_gmt":"2024-10-25T09:14:41","slug":"bs-en-60939-22005-2006","status":"publish","type":"product","link":"https:\/\/pdfstandards.shop\/product\/publishers\/bsi\/bs-en-60939-22005-2006\/","title":{"rendered":"BS EN 60939-2:2005 2006"},"content":{"rendered":"

PDF Catalog<\/h4>\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n
PDF Pages<\/th>\nPDF Title<\/th>\n<\/tr>\n
9<\/td>\nGeneral
Scope
Normative references <\/td>\n<\/tr>\n
10<\/td>\nInformation to be given in a detail specification
General
Outline drawing and dimensions
Mounting <\/td>\n<\/tr>\n
11<\/td>\nRatings and characteristics
General
Particular characteristics
Marking
Terms and definitions <\/td>\n<\/tr>\n
12<\/td>\nMarking
See 2.4 of IEC\u00a060939-1 with the following details: <\/td>\n<\/tr>\n
13<\/td>\nThe filter shall be clearly marked with the information in 1.5.1 a), b), c) and d), and also e) if this is not implied by b).
The package containing the filter(s) shall be clearly marked
Any additional marking shall be so applied that no confusion
Preferred ratings and characteristics
Preferred characteristics
General
Preferred climatic categories
Preferred values of ratings
Rated voltage (UR)
Category voltage (UC) <\/td>\n<\/tr>\n
14<\/td>\nRated temperature
Passive flammability
Quality assessment procedures
Primary stage of manufacture
Structurally similar filters
Certified records of released lots
Approval testing
Safety tests only approval
Qualification approval <\/td>\n<\/tr>\n
15<\/td>\nSampling
Tests <\/td>\n<\/tr>\n
16<\/td>\nQuality conformance inspection
General
Formation of inspection lots <\/td>\n<\/tr>\n
17<\/td>\nTest schedule
Delayed delivery <\/td>\n<\/tr>\n
20<\/td>\nTest and measurement procedures
Earth inductors incorporated in filters
General <\/td>\n<\/tr>\n
21<\/td>\nCapacitance and tan ( measurements
Visual examination and check of dimensions
Creepage distances and clearances <\/td>\n<\/tr>\n
22<\/td>\nVoltage proof
Test circuit for d.c. tests
Applied voltage <\/td>\n<\/tr>\n
23<\/td>\nRequirements
Insulation resistance
Temperature correction
Requirements
DC line resistance or voltage drop at rated current
DC line resistance <\/td>\n<\/tr>\n
24<\/td>\nVoltage drop at rated current
Insertion loss
Discharge resistance <\/td>\n<\/tr>\n
25<\/td>\nRobustness of terminations
Resistance to soldering heat
Test conditions
Intermediate inspection, measurements and requirements
Solderability
Test conditions
Requirements
Rapid change of temperature <\/td>\n<\/tr>\n
26<\/td>\nIntermediate inspection
Vibration
Test conditions
Intermediate inspection
Bump
Test conditions
Intermediate inspection, measurements and requirements <\/td>\n<\/tr>\n
27<\/td>\nShock
Test conditions
Intermediate inspection, measurements and requirements
Container sealing
Test conditions
Requirements <\/td>\n<\/tr>\n
28<\/td>\nClimatic sequence
Initial measurements
Dry heat
Damp heat, cyclic, first cycle
Cold
Low air pressure
Damp heat, cyclic, remaining cycles
Final inspection, measurements and requirements <\/td>\n<\/tr>\n
29<\/td>\nDamp heat, steady state
Test conditions
Final inspection, measurements and requirements
Temperature rise <\/td>\n<\/tr>\n
30<\/td>\nTest method <\/td>\n<\/tr>\n
31<\/td>\nRequirements
Impulse voltage
Initial measurements
Test conditions <\/td>\n<\/tr>\n
32<\/td>\nRequirements
Endurance
Test conditions \u2013 current test <\/td>\n<\/tr>\n
33<\/td>\nTest conditions \u2013 voltage test, terminations\/case
Test conditions \u2013 voltage test between terminations <\/td>\n<\/tr>\n
34<\/td>\nTest conditions \u2013 combined voltage\/current tests
Final inspection, measurements and requirements
Charge and discharge <\/td>\n<\/tr>\n
35<\/td>\nInitial measurements
Test conditions
Final measurements and requirements
Passive flammability
Current overload
Solvent resistance of the marking <\/td>\n<\/tr>\n
36<\/td>\nComponent solvent resistance
Active flammability <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":"

Passive filter units for electromagnetic interference suppression – Sectional specification: passive filter units for which safety tests are appropriate. Test methods and general requirements<\/b><\/p>\n\n\n\n\n
Published By<\/td>\nPublication Date<\/td>\nNumber of Pages<\/td>\n<\/tr>\n
BSI<\/b><\/a><\/td>\n2006<\/td>\n50<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n","protected":false},"featured_media":230471,"template":"","meta":{"rank_math_lock_modified_date":false,"ep_exclude_from_search":false},"product_cat":[2641],"product_tag":[],"class_list":{"0":"post-230468","1":"product","2":"type-product","3":"status-publish","4":"has-post-thumbnail","6":"product_cat-bsi","8":"first","9":"instock","10":"sold-individually","11":"shipping-taxable","12":"purchasable","13":"product-type-simple"},"_links":{"self":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product\/230468","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product"}],"about":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/types\/product"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/media\/230471"}],"wp:attachment":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/media?parent=230468"}],"wp:term":[{"taxonomy":"product_cat","embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product_cat?post=230468"},{"taxonomy":"product_tag","embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product_tag?post=230468"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}