{"id":165992,"date":"2024-10-19T10:04:48","date_gmt":"2024-10-19T10:04:48","guid":{"rendered":"https:\/\/pdfstandards.shop\/product\/uncategorized\/sd-southdakotaplumbingcode-2015\/"},"modified":"2024-10-25T02:24:19","modified_gmt":"2024-10-25T02:24:19","slug":"sd-southdakotaplumbingcode-2015","status":"publish","type":"product","link":"https:\/\/pdfstandards.shop\/product\/publishers\/sd\/sd-southdakotaplumbingcode-2015\/","title":{"rendered":"SD SouthDakotaPlumbingCode 2015"},"content":{"rendered":"

The 2015 edition of the South Dakota Plumbing Code (SDPC) represents the most current approaches in the plumbing field. This code is embedded with the 2015 Edition of the Uniform Plumbing Code (UPC\u00ae) with the South Dakota amendments. It is the fifth edition developed under the American National Standards Institute (ANSI) process. Contributions to the content of this code were made by every segment of the built industry, including such diverse interests as consumers, enforcing authorities, installers\/maintainers, labor, manufacturers, research\/standards\/ testing laboratories, special experts, and users. The SDPC is designed to provide consumers with safe and sanitary plumbing systems while, at the same time, allowing latitude for innovation and new technologies. Key changes to the 2015 SDPC include: \u2022 New product standards and flow rates for plumbing fixtures and fixture fittings. (Chapter 4). \u2022 Lead-content provisions have been revised to address the minimum acceptable percentage lead content for pipes and fittings (Chapter 6). \u2022 New provisions for residential fire sprinkler systems (Chapter 6). \u2022 New requirements for the discharge piping serving a temperature relief valve, pressure relief valve, or combination of both (Chapter 6). \u2022 New testing requirements for the hot and cold water supply system (Chapter 6). \u2022 Additional materials added for drain, waste, and vent pipe and fittings (Chapter 7). \u2022 New testing requirement for drain, and vent piping (Chapter 7). \u2022 Additional venting methods for island sinks (Chapter 9).<\/p>\n

PDF Catalog<\/h4>\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n
PDF Pages<\/th>\nPDF Title<\/th>\n<\/tr>\n
2<\/td>\nPreface <\/td>\n<\/tr>\n
4<\/td>\nImportant Notices and Disclaimers
Updating IAPMO Codes <\/td>\n<\/tr>\n
5<\/td>\nForeword
Origin and Development <\/td>\n<\/tr>\n
6<\/td>\nAdoption
Revision Markings <\/td>\n<\/tr>\n
7<\/td>\nFormat of the Uniform Plumbing Code <\/td>\n<\/tr>\n
12<\/td>\nCommittee on Uniform Plumbing Code <\/td>\n<\/tr>\n
14<\/td>\nTable of Contents
Chapter 1 Administration
Chapter 2 Definitions
Chapter 3 General Regulations <\/td>\n<\/tr>\n
15<\/td>\nChapter 4 Plumbing Fixtures and Fixture Fittings <\/td>\n<\/tr>\n
17<\/td>\nChapter 5 Water Heaters (Reserved)
Chapter 6 Water Supply and Distribution <\/td>\n<\/tr>\n
19<\/td>\nChapter 7 Sanitary Drainage <\/td>\n<\/tr>\n
20<\/td>\nChapter 8 Indirect Wastes <\/td>\n<\/tr>\n
21<\/td>\nChapter 9 Vents <\/td>\n<\/tr>\n
22<\/td>\nChapter 10 Traps and Interceptors
Chapter 11 Storm Drainage <\/td>\n<\/tr>\n
23<\/td>\nChapter 12 Fuel Gas Piping (Reserved)
Chapter 13 Health Care Facilities and Medical Gas and Medical Vacuum Systems (Reserved)
Chapter 14 Firestop Protection (Reserved)
Chapter 15 Alternate Water Sources for Nonpotable Applications (Reserved)
Chapter 16 Nonpotable Rainwater Catchment Systems (Reserved)
Chapter 17 Referenced Standards
Appendices Table of Contents
Appendix A Recommended Rules for Sizing the Water Supply System
Appendix B Explanatory Notes on Combination Waste and Vent Systems
Appendix C Alternate Plumbing Systems
Appendix D Sizing Storm Water Drainage Systems
Appendix E Manufactured\/Mobile Home Parks and Recreational Vehicle Parks
Appendix F Firefighter Breathing Air Replenishment Systems (Reserved)
Appendix G Sizing of Venting Systems (Reserved)
Appendix H Private Sewage Disposal Systems (Reserved) .
Appendix I Installation Standard
Appendix J Combination of Indoor and Outdoor Combustion and Ventilation Opening Design (Reserved)
Appendix K Potable Rainwater Catchment Systems (Reserved) .
Appendix L Sustainable Practices (Reserved)
Index <\/td>\n<\/tr>\n
24<\/td>\nChapter 1 Administration
101.0 General.
101.1 Title.
101.2 Scope.
101.3 Purpose.
101.4 Unconstitutional.
101.5 Validity.
102.0 Applicability.
102.1 Conflicts Between Codes.
102.2 Existing Installations.
102.3 Maintenance.
102.4 Additions, Alterations, or Renovations.
102.4.1 Building Sewers and Drains.
102.4.2 Openings.
102.5 Health and Safety.
102.6 Changes in Building Occupancy.
102.7 Moved Structures.
102.8 Appendices.
TABLE <\/td>\n<\/tr>\n
25<\/td>\n103.0 Duties and Powers of the Authority Having Jurisdiction.
103.1 General.
103.2 Liability.
103.3 Applications and Permits.
103.3.1 Licensing.
103.4 Right of Entry.
104.0 Permits.
104.1 Permits Required.
104.2 Exempt Work.
104.3 Application for Permit.
104.3.1 Construction Documents.
104.3.2 Plan Review Fees.
104.3.3 Time Limitation of Application.
104.4 Permit Issuance.
104.4.1 Approved Plans or Construction Documents.
104.4.2 Validity of Permit.
104.4.3 Expiration.
104.4.4 Extensions.
104.4.5 Suspension or Revocation.
104.4.6 Retention of Plans.
104.5 Fees.
104.5.1 Work Commencing Before Permit Issuance.
104.5.2 Investigation Fees.
104.5.3 Fee Refunds.
105.0 Inspections and Testing.
105.1 General.
105.2 Required Inspections.
105.2.1 Uncovering.
105.2.1.1 Water Supply System.
105.2.1.2 Covering or Using.
105.2.2 Other Inspections.
105.2.3 Inspection Requests.
105.2.4 Advance Notice.
105.2.5 Responsibility.
105.2.6 Reinspections.
105.3 Testing of Systems.
105.3.1 Defective Systems.
105.3.2 Retesting.
105.3.3 Approval.
105.4 Connection to Service Utilities.
106.0 Violations and Penalties.
106.1 General.
106.2 Notices of Correction or Violation.
106.3 Penalties.
106.4 Stop Orders.
106.5 Authority to Disconnect Utilities in Emergencies.
106.6 Authority to Condemn.
107.0 Board of Appeals.
107.1 General.
107.2 Limitations of Authority.
Table 104.5 Plumbing Permit Fees <\/td>\n<\/tr>\n
26<\/td>\nChapter 2 Definitions
201.0 General.
201.1 Applicability.
202.0 Definition of Terms.
202.1 General.
203.0 \u2013 A \u2013
204.0 \u2013 B \u2013 <\/td>\n<\/tr>\n
27<\/td>\n205.0 \u2013 C \u2013 <\/td>\n<\/tr>\n
28<\/td>\n206.0 \u2013 D \u2013
207.0 \u2013 E \u2013
208.0 \u2013 F \u2013 <\/td>\n<\/tr>\n
29<\/td>\n209.0 \u2013 G \u2013
210.0 \u2013 H \u2013
211.0 \u2013 I \u2013 <\/td>\n<\/tr>\n
30<\/td>\n212.0 \u2013 J \u2013
213.0 \u2013 K \u2013
214.0 \u2013 L \u2013
215.0 \u2013 M \u2013 <\/td>\n<\/tr>\n
31<\/td>\n216.0 \u2013 N \u2013
217.0 \u2013 O \u2013
218.0 \u2013 P \u2013 <\/td>\n<\/tr>\n
32<\/td>\n219.0 \u2013 Q \u2013
220.0 \u2013 R \u2013
221.0 \u2013 S \u2013 <\/td>\n<\/tr>\n
33<\/td>\n222.0 \u2013 T \u2013
223.0 \u2013 U \u2013
224.0 \u2013 V \u2013
225.0 \u2013 W \u2013 <\/td>\n<\/tr>\n
34<\/td>\n226.0 \u2013 X \u2013
227.0 \u2013 Y \u2013
228.0 \u2013 Z \u2013 <\/td>\n<\/tr>\n
36<\/td>\nChapter 3 General Regulations
301.0 General.
301.1 Applicability.
301.2 Minimum Standards.
301.2.1 Marking.
301.2.2 Standards.
301.2.3 Plastic Pipe, Plastic Pipe Fittings, and Components.
301.2.4 Cast-Iron Soil Pipe and Fittings.
301.2.5 Existing Buildings.
301.3 Alternate Materials and Methods of Construction Equivalency.
301.3.1 Testing.
301.3.1.1 Tests.
301.3.1.2 Request by Authority Having Jurisdiction.
301.4 Flood Hazard Areas.
TABLES <\/td>\n<\/tr>\n
37<\/td>\n301.4.1 Coastal High Hazard Areas.
301.5 Alternative Engineered Design.
301.5.1 Permit Application.
301.5.2 Technical Data.
301.5.3 Design Documents.
301.5.4 Design Approval.
301.5.5 Design Review.
301.5.6 Inspection and Testing.
302.0 Iron Pipe Size (IPS) Pipe.
302.1 General.
303.0 Disposal of Liquid Waste.
303.1 General.
304.0 Connections to Plumbing System Required.
304.1 General.
305.0 Damage to Drainage System or Public Sewer.
305.1 Unlawful Practices.
306.0 Industrial Wastes.
306.1 Detrimental Wastes.
306.2 Safe Discharge.
307.0 Location.
307.1 System.
307.2 Ownership.
308.0 Improper Location.
308.1 General.
309.0 Workmanship.
309.1 Engineering Practices. <\/td>\n<\/tr>\n
38<\/td>\n309.2 Concealing Imperfections.
309.3 Burred Ends.
309.4 Installation Practices.
310.0 Prohibited Fittings and Practices.
310.1 Fittings.
310.2 Drainage and Vent Piping.
310.3 Waste Connection.
310.4 Use of Vent and Waste Pipes.
310.5 Obstruction of Flow.
310.6 Dissimilar Metals.
310.7 Direction of Flow.
310.8 Screwed Fittings.
311.0 Independent Systems.
311.1 General.
312.0 Protection of Piping, Materials, and Structures.
312.1 General.
312.2 Installation.
312.3 Building Sewer and Drainage Piping.
312.4 Corrosion, Erosion, and Mechanical Damage.
312.5 Protectively Coated Pipe.
312.6 Freezing Protection.
312.7 Fire-Resistant Construction. <\/td>\n<\/tr>\n
39<\/td>\n312.8 Waterproofing of Openings.
312.9 Steel Nail Plates.
312.10 Sleeves.
312.10.1 Building Loads.
312.10.2 Exterior Walls.
312.10.3 Firewalls.
312.11 Structural Members.
312.12 Rodentproofing.
312.12.1 Meter Boxes.
312.12.2 Collars.
312.12.3 Tub Waste Openings.
312.13 Exposed ABS Piping.
312.14 Exposed PVC Piping.
313.0 Hangers and Supports.
313.1 General.
313.2 Material.
313.3 Suspended Piping.
313.4 Alignment.
313.5 Underground Installation.
313.6 Hanger Rod Sizes.
313.7 Gas Piping.
314.0 Trenching, Excavation, and Backfill.
314.1 Trenches.
314.2 Tunneling and Driving.
314.3 Open Trenches.
314.4 Excavations.
314.4.1 Installation of Thermoplastic Pipe and Fittings.
Table 313.6 Hanger Rod Sizes <\/td>\n<\/tr>\n
40<\/td>\n315.0 Joints and Connections.
315.1 Unions.
315.2 Prohibited Joints and Connections.
316.0 Increasers and Reducers.
316.1 General.
317.0 Food-Handling Establishments.
317.1 General.
318.0 Test Gauges.
318.1 General.
318.2 Pressure Tests (10 psi or less).
318.3 Pressure Tests (greater than 10 psi to 100 psi).
318.4 Pressure Tests (exceeding 100 psi).
318.5 Pressure Range.
319.0 Medical Gas and Vacuum Systems.
319.1 General.
320.0 Rehabilitation of Piping Systems.
320.1 General. <\/td>\n<\/tr>\n
41<\/td>\nTable 313.3 Hangers and Supports <\/td>\n<\/tr>\n
42<\/td>\nChapter 4 Plumbing Fixtures and Fixture Fittings
401.0 General.
401.1 Applicability.
401.2 Quality of Fixtures.
402.0 Installation.
402.1 Cleaning.
402.2 Joints.
402.3 Securing Fixtures.
402.4 Wall-Hung Fixtures.
402.5 Setting.
402.6 Flanged Fixture Connections.
402.6.1 Closet Rings (Closet Flanges).
402.6.2 Securing Closet Flanges.
402.6.3 Securing Floor-Mounted, Back-Outlet Water Closet Bowls.
402.7 Supply Fittings.
402.8 Installation.
TABLE <\/td>\n<\/tr>\n
43<\/td>\n402.9 Design and Installation of Plumbing Fixtures.
402.10 Slip Joint Connections.
402.11 Future Fixtures.
403.0 Accessible Plumbing Facilities.
403.1 General.
403.2 Fixtures and Fixture Fittings for Persons with Disabilities.
403.3 Exposed Pipes and Surfaces.
404.0 Overflows.
404.1 General.
405.0 Prohibited Fixtures.
405.1 Prohibited Water Closets.
405.2 Prohibited Urinals.
405.3 Miscellaneous Fixtures.
406.0 Special Fixtures and Specialties.
406.1 Water and Waste Connections.
406.2 Special Use Sinks.
406.3 Special Use Fixtures.
406.4 Zinc Alloy Components.
407.0 Lavatories.
407.1 Application.
407.2 Water Consumption.
407.2.1 Maximum Flow Rate.
407.2.2 Metering Faucets.
407.3 Limitation of Hot Water Temperature for Public Lavatories. <\/td>\n<\/tr>\n
44<\/td>\n407.4 Transient Public Lavatories.
407.5 Waste Outlet.
407.6 Overflow.
408.0 Showers.
408.1 Application.
408.2 Water Consumption.
408.3 Individual Shower and Tub-Shower Combination Control Valves.
408.4 Waste Outlet.
408.5 Finished Curb or Threshold.
408.6 Shower Compartments.
408.7 Lining for Showers and Receptors. <\/td>\n<\/tr>\n
45<\/td>\n408.7.1 PVC Sheets.
408.7.2 Chlorinated Polyethylene (CPE) Sheets.
408.7.3 Sheet Lead.
408.7.4 Sheet Copper.
408.7.5 Tests for Shower Receptors.
408.8 Public Shower Floors.
408.9 Location of Valves and Heads.
408.10 Water Supply Riser.
409.0 Bathtubs and Whirlpool Bathtubs.
409.1 Application.
409.2 Waste Outlet.
409.3 Overflow.
409.4 Limitation of Hot Water in Bathtubs and Whirlpool Bathtubs.
409.5 Backflow Protection.
409.6 Installation and Access. <\/td>\n<\/tr>\n
46<\/td>\n409.6.1 Flexible PVC Hoses and Tubing.
410.0 Bidets.
410.1 Application.
410.2 Backflow Protection.
410.3 Limitation of Water Temperature in Bidets.
411.0 Water Closets.
411.1 Application.
411.2 Water Consumption.
411.2.1 Dual Flush Water Closets.
411.2.2 Flushometer Valve Activated Water Closets.
411.3 Water Closet Seats.
412.0 Urinals.
412.1 Application.
412.1.1 Nonwater Urinals.
412.2 Backflow Protection.
413.0 Flushing Devices.
413.1 Where Required.
413.2 Flushometer Valves.
413.3 Flush Tanks. <\/td>\n<\/tr>\n
47<\/td>\n413.4 Water Supply for Flush Tanks.
413.5 Overflows in Flush Tanks.
414.0 Dishwashing Machines.
414.1 Application.
414.2 Backflow Protection.
414.3 Drainage Connection.
415.0 Drinking Fountains.
415.1 Application.
415.2 Drinking Fountain Alternatives.
415.3 Drainage Connection.
415.4 Location.
416.0 Emergency Eyewash and Shower Equipment.
416.1 Application.
416.2 Water Supply.
416.3 Installation.
416.4 Location.
416.5 Drain.
417.0 Faucets and Fixture Fittings.
417.1 Application.
417.2 Deck Mounted Bath\/Shower Valves.
417.3 Handheld Showers.
417.4 Faucets and Fixture Fittings with Hose Connected Outlets.
417.5 Separate Controls for Hot and Cold Water.
418.0 Floor Drains.
418.1 Application. <\/td>\n<\/tr>\n
48<\/td>\n418.2 Strainer.
418.3 Location of Floor Drains.
418.4 Food Storage Areas.
418.5 Floor Slope.
419.0 Food Waste Disposers.
419.1 Application.
419.2 Drainage Connection.
419.3 Water Supply.
420.0 Sinks.
420.1 Application.
420.2 Water Consumption.
420.3 Pre-Rinse Spray Valve.
420.4 Waste Outlet.
421.0 Floor Sinks.
421.1 Application.
421.2 Strainers.
422.0 Minimum Number of Required Fixtures.
422.1 Fixture Count.
422.1.1 Family or Assisted-Use Toilet and Bathing Facilities. <\/td>\n<\/tr>\n
49<\/td>\n422.2 Separate Facilities.
422.2.1 Family or Assisted-Use Toilet Facilities.
422.3 Fixture Requirements for Special Occupancies.
422.4 Toilet Facilities Serving Employees and Customers.
422.4.1 Access to Toilet Facilities.
422.5 Toilet Facilities for Workers. <\/td>\n<\/tr>\n
50<\/td>\nTable 422.1 Minimum Plumbing Facilities <\/td>\n<\/tr>\n
54<\/td>\nChapter 5 Water Heaters <\/td>\n<\/tr>\n
56<\/td>\nChapter 6 Water Supply and Distribution
601.0 General.
601.1 Applicability.
601.2 Hot and Cold Water Required.
601.3 Identification of a Potable and Nonpotable Water System.
601.3.1 Potable Water.
601.3.2 Color and Information.
601.3.3 Alternate Water Sources.
601.3.4 Fixtures.
601.3.5 Outlets.
602.0 Unlawful Connections.
602.1 Prohibited Installation.
TABLES
Table 601.3.2 Minimum Length of Color Field and Size of Letters <\/td>\n<\/tr>\n
57<\/td>\n602.2 Cross-Contamination.
602.3 Backflow Prevention.
602.4 Approval by Authority.
603.0 Cross-Connection Control.
603.1 General.
603.2 Approval of Devices or Assemblies.
603.3 Backflow Prevention Devices, Assemblies, and Methods.
603.3.1 Air Gap.
603.3.2 Atmospheric Vacuum Breaker (AVB).
603.3.3 Hose Connection Backflow Preventer.
603.3.4 Double Check Valve Backflow Prevention Assembly (DC).
603.3.5 Pressure Vacuum Breaker Backflow Prevention Assembly (PVB).
603.3.6 Spill-Resistant Pressure Vacuum Breaker (SVB).
603.3.7 Reduced-Pressure Principle Backflow Prevention Assembly (RP).
603.3.8 Double Check Detector Fire Protection Backflow Prevention Assembly. <\/td>\n<\/tr>\n
58<\/td>\nTable 603.2 Backflow Prevention Devices, Assemblies, and Methods <\/td>\n<\/tr>\n
60<\/td>\n603.3.9 Reduced Pressure Detector Fire ProtectionBackflow Prevention Assembly.
603.4 General Requirements.
603.4.1 Backflow Prevention Valve.
603.4.2 Testing.
603.4.3 Access and Clearance.
603.4.4 Connections.
603.4.5 Hot Water Backflow Preventers.
603.4.6 Integral Backflow Preventers.
603.4.7 Freeze Protection.
Table 603.3.1 Minimum Air Gaps for Water Distibution <\/td>\n<\/tr>\n
61<\/td>\n603.4.8 Drain Lines.
603.4.9 Prohibited Locations.
603.5 Specific Requirements.
603.5.1 Atmospheric Vacuum Breaker.
603.5.2 Ballcock.
603.5.3 Backflow Prevention.
603.5.4 Heat Exchangers.
603.5.5 Water Supply Inlets.
603.5.6 Protection from Lawn Sprinklers and Irrigation Systems.
603.5.6.1 Systems with Pumps.
603.5.6.2 Systems with Backflow Devices.
603.5.6.3 Systems with Chemical Injectors.
603.5.7 Outlets with Hose Attachments.
603.5.8 Water-Cooled Equipment. <\/td>\n<\/tr>\n
62<\/td>\n603.5.9 Aspirators.
603.5.10 Steam or Hot Water Boilers.
603.5.11 Nonpotable Water Piping.
603.5.12 Beverage Dispensers.
603.5.13 Deck-Mounted and Equipment-Mounted Vacuum Breakers.
603.5.14 Protection from Fire Systems.
603.5.14.1 Fire Department Connection.
603.5.14.2 Chemicals.
603.5.14.3 Hydraulic Design.
603.5.15 Health Care or Laboratory Areas.
603.5.16 Special Equipment.
603.5.17 Potable Water Outlets and Valves. <\/td>\n<\/tr>\n
63<\/td>\n603.5.18 Pure Water Process Systems.
603.5.18.1 Dialysis Water Systems.
603.5.19 Plumbing Fixture Fittings.
603.5.20 Swimming Pools, Spas, and Hot Tubs.
604.0 Materials.
604.1 Pipe, Tube, and Fittings.
604.2 Lead Content.
604.2.1 Lead Content of Water Supply Pipe and Fittings.
604.3 Copper or Copper Alloy Tube.
604.4 Hard-Drawn Copper or Copper Alloy Tubing.
604.5 Flexible Connectors.
604.6 Cast-Iron Fittings.
604.7 Malleable Iron Fittings.
604.8 Previously Used Piping and Tubing.
604.9 Epoxy Coating.
604.10 Plastic Materials.
604.10.1 Tracer Wire.
604.11 Solder. <\/td>\n<\/tr>\n
64<\/td>\n604.12 Flexible Corrugated Connectors.
604.13 Water Heater Connectors.
605.0 Joints and Connections.
605.1 Copper or Copper Alloy Pipe, Tubing, and Joints.
605.1.1 Brazed Joints.
Table 604.1 Materials for Building Supply and Water Distribution Piping and Fittings <\/td>\n<\/tr>\n
65<\/td>\n605.1.2 Flared Joints.
605.1.3 Mechanical Joints.
605.1.3.1 Mechanically Formed Tee Fittings.
605.1.3.2 Pressed Fittings.
605.1.3.3 Push Fit Fittings.
605.1.4 Soldered Joints.
605.1.5 Threaded Joints.
605.2 CPVC Plastic Pipe and Joints.
605.2.1 Mechanical Joints.
605.2.2 Solvent Cement Joints. <\/td>\n<\/tr>\n
66<\/td>\n605.2.3 Threaded Joints.
605.3 CPVC\/AL\/CPVC Plastic Pipe and Joints.
605.3.1 Solvent Cement Joints.
605.4 Ductile Iron Pipe and Joints.
605.4.1 Mechanical Joints.
605.4.2 Push-On Joints.
605.5 Galvanized Steel Pipe and Joints.
605.5.1 Mechanical Joints.
605.5.2 Threaded Joints.
605.6 PE Plastic Pipe\/Tubing and Joints.
605.6.1 Heat-Fusion Joints.
605.6.1.1 Butt-Fusion Joints.
605.6.1.2 Electro-Fusion Joints.
605.6.1.3 Socket-Fusion Joints.
605.6.2 Mechanical Joints. <\/td>\n<\/tr>\n
67<\/td>\n605.7 PE-AL-PE Plastic Pipe\/Tubing and Joints.
605.7.1 Mechanical Joints.
605.7.1.1 Compression Joints.
605.8 PE-RT.
605.8.1 Fittings.
605.9 PEX Plastic Tubing and Joints.
605.9.1 Fittings.
605.9.2 Mechanical Joints.
605.10 PEX-AL-PEX Plastic Tubing and Joints.
605.10.1 Mechanical Joints.
605.10.1.1 Compression Joints.
605.11 Polypropylene (PP) Piping and Joints.
605.11.1 Heat-Fusion Joints.
605.11.2 Mechanical and Compression Sleeve Joints.
605.11.3 Threaded Joints.
605.12 PVC Plastic Pipe and Joints. <\/td>\n<\/tr>\n
68<\/td>\n605.12.1 Mechanical Joints.
605.12.2 Solvent Cement Joints.
605.12.3 Threaded Joints.
605.13 Stainless Steel Pipe and Joints.
605.13.1 Mechanical Joints.
605.13.2 Welded Joints.
605.14 Slip Joints.
605.15 Dielectric Unions.
605.16 Joints Between Various Materials.
605.16.1 Copper or Copper Alloy Pipe or Tubing to Threaded Pipe Joints.
605.16.2 Plastic Pipe to Other Materials.
605.16.3 Stainless Steel to Other Materials.
606.0 Valves.
606.1 General.
606.2 Fullway Valve.
606.3 Multidwelling Units. <\/td>\n<\/tr>\n
69<\/td>\n606.4 Multiple Openings.
606.5 Control Valve.
606.6 Accessible.
606.7 Multiple Fixtures.
607.0 Potable Water Supply Tanks.
607.1 General.
607.2 Potable Water Tanks.
607.3 Venting.
607.4 Overflow.
607.5 Valves.
608.0 Water Pressure, Pressure Regulators, Pressure Relief Valves, and Vacuum Relief Valves.
608.1 Inadequate Water Pressure.
608.2 Excessive Water Pressure.
608.3 Expansion Tanks, and Combination Temperature and Pressure-Relief Valves. <\/td>\n<\/tr>\n
70<\/td>\n608.4 Pressure Relief Valves.
608.5 Discharge Piping.
608.6 Water-Heating Devices.
608.7 Vacuum Relief Valves.
609.0 Installation, Testing, Unions, and Location.
609.1 Installation.
609.2 Trenches.
609.3 Under Concrete Slab.
609.4 Testing.
609.5 Unions.
609.6 Location.
609.7 Abutting Lot.
609.8 Low-Pressure Cutoff Required on Booster Pumps for Water Distribution Systems.
609.9 Disinfection of Potable Water System. <\/td>\n<\/tr>\n
71<\/td>\n609.10 Water Hammer.
609.10.1 Mechanical Devices.
609.11 Pipe Insulation.
609.11.1 Insulation Requirements.
609.11.2 Pipe Insulation Wall Thickness.
610.0 Size of Potable Water Piping.
610.1 Size.
610.2 Pressure Loss.
610.3 Quantity of Water.
610.4 Sizing Water Supply and Distribution Systems.
610.5 Sizing per Appendices A and C.
610.6 Friction and Pressure Loss.
610.7 Conditions for Using Table 610.4.
610.8 Size of Meter and Building Supply Pipe Using Table 610.4. <\/td>\n<\/tr>\n
72<\/td>\nTable 610.3 Water Supply Fixture Units (WSFU) and Minimum Fixture Branch Pipe Sizes <\/td>\n<\/tr>\n
73<\/td>\nTable 610.4 Fixture Unit Table for Determining Water Pipe and Meter Sizes <\/td>\n<\/tr>\n
74<\/td>\n610.9 Size of Branches.
610.10 Sizing for Flushometer Valves.
Table 610.10 Flushometer Fixture Units for Water Sizing Using Table 610.3 <\/td>\n<\/tr>\n
75<\/td>\n610.11 Sizing Systems for Flushometer Tanks.
610.12 Sizing for Velocity.
610.12.1 Copper Tube Systems.
610.12.2 Tubing Systems Using Copper Fittings.
610.13 Exceptions.
611.0 Drinking Water Treatment Units.
611.1 Application.
611.2 Air Gap Discharge.
611.3 Connection Tubing.
611.4 Sizing of Residential Softeners.
612.0 Residential Fire Sprinkler Systems.
612.1 Where Required. <\/td>\n<\/tr>\n
76<\/td>\n612.2 Types of Systems.
612.3 Sprinklers.
612.3.1 Required Sprinkler Locations.
612.3.2 Sprinkler Installation.
612.3.3 Temperature Rating and Separation from Heat Sources.
612.3.3.1 Intermediate Temperature Sprinklers.
612.3.4 Freezing Areas.
612.3.5 Coverage Area Limit.
612.3.6 Obstructions to Sprinkler Coverage.
Table 611.4 Sizing of Residential Water Softeners <\/td>\n<\/tr>\n
77<\/td>\n612.3.6.1 Additional Requirements for Pendent Sprinklers.
612.3.6.2 Additional Requirements for Sidewall Sprinklers.
612.3.7 Sprinkler Modifications Prohibited.
612.4 Sprinkler Piping System.
612.4.1 General.
612.4.2 Nonmetallic Pipe and Tubing.
612.4.2.1 Nonmetallic Pipe Protection.
612.4.2.2 Sprinkler Installation on Systems Assembled with Solvent Cement.
612.4.3 Shutoff Valves Prohibited.
612.4.4 Single Dwelling Limit.
612.4.5 Drain.
612.5 Sprinkler Piping Design.
612.5.1 Determining System Design Flow.
612.5.1.1 Determining Required Flow Rate for Each Sprinkler.
Table 612.3.3.1 Locations Where Intermediate Temperature Sprinklers are Required <\/td>\n<\/tr>\n
78<\/td>\nTable 612.3.6 Minimum Separation from Obstruction <\/td>\n<\/tr>\n
79<\/td>\n612.5.1.2 System Flow Rate.
612.5.2 Sprinkler Pipe Water Supply.
612.5.2.1 Water Pressure from Individual Sources.
612.5.2.2 Required Capacity.
612.5.3 Sprinkler Pipe Sizing.
612.5.3.1 Sprinkler Pipe Sizing Method.
612.5.3.2 Prescriptive Pipe Sizing Method.
612.5.3.2.1 Available Pressure Equation.
612.5.3.2.2 Calculation Procedure. <\/td>\n<\/tr>\n
80<\/td>\nTable 612.5.3.2(1) Water Service Pressure Loss (PLws) <\/td>\n<\/tr>\n
81<\/td>\n612.6 Instructions and Signs.
612.7 Inspection and Testing.
612.7.1 Pre-Concealment Inspection.
612.7.2 Final Inspection.
Table 612.5.3.2(2) Minimum Water Meter Pressure Loss (PLm)
Table 612.5.3.2(3) Elevation Loss (PLe) <\/td>\n<\/tr>\n
82<\/td>\nTable 612.5.3.2(4) Allowable Pipe Length for 3\u20444 Inch Type M Copper Water Tubing <\/td>\n<\/tr>\n
83<\/td>\nTable 612.5.3.2(5) Allowable Pipe Length for 1 Inch Type M Copper Water Tubing <\/td>\n<\/tr>\n
84<\/td>\nTable 612.5.3.2(6) Allowable Pipe Length for 3\u20444 Inch IPS CPVC Pipe <\/td>\n<\/tr>\n
85<\/td>\nTable 612.5.3.2(7) Allowable Pipe Length for 1 Inch IPS CPVC Pipe <\/td>\n<\/tr>\n
86<\/td>\nTable 612.5.3.2(8) Allowable Pipe Length for 3\u20444 Inch PEX Tubing <\/td>\n<\/tr>\n
87<\/td>\nTable 612.5.3.2(9) Allowable Pipe Length for 1 Inch PEX Tubing <\/td>\n<\/tr>\n
88<\/td>\nChapter 7 Sanitary Drainage
Part I \u2013 Drainage Systems.
701.0 General.
701.1 Applicability.
701.2 Drainage Piping.
701.3 Drainage Fittings.
701.3.1 Screwed Pipe.
701.3.2 Threads.
701.3.3 Type.
701.4 Continuous Wastes.
701.5 Lead.
701.6 Caulking Ferrules.
701.7 Soldering Bushings.
702.0 Fixture Unit Equivalents.
702.1 Trap Size.
TABLES
Table 701.6 Caulking Ferrules
Table 701.7 Soldering Bushings <\/td>\n<\/tr>\n
89<\/td>\nTable 701.2 Materials for Drain, Waste, Vent Pipe and Fittings <\/td>\n<\/tr>\n
90<\/td>\nTable 702.1 Drainage Fixture Unit Values (DFU) <\/td>\n<\/tr>\n
91<\/td>\n702.2 Intermittent Flow.
702.3 Continuous Flow.
703.0 Size of Drainage Piping.
703.1 Minimum Size.
703.2 Maximum Number of Fixture Units.
703.3 Sizing per Appendix C.
704.0 Fixture Connections (Drainage).
704.1 Inlet Fittings.
704.2 Single Vertical Drainage Pipe.
704.3 Commercial Sinks.
705.0 Joints and Connections.
705.1 ABS and ABS Co-Extruded Plastic Pipe and Joints.
705.1.1 Mechanical Joints.
705.1.2 Solvent Cement Joints.
705.1.3 Threaded Joints.
705.2 Cast-Iron Pipe and Joints.
705.2.1 Caulked Joints.
Table 702.2(1) Maximum Drainage Fixture Units for a Trap and Trap Arm
Table 702.2(2) Discharge Capacity in Gallons per Minute for Intermittent Flow Only <\/td>\n<\/tr>\n
92<\/td>\n705.2.2 Mechanical Joints and Compression Joints.
705.3 Copper or Copper Alloy Pipe (DWV) and Joints.
705.3.1 Brazed Joints.
705.3.2 Mechanical Joints.
705.3.3 Soldered Joints.
Table 703.2 Maximum Unit Loading and Maximum Length of Drainage and Vent Piping <\/td>\n<\/tr>\n
93<\/td>\n705.3.4 Threaded Joints.
705.4 Galvanized Steel Pipe and Joints.
705.4.1 Mechanical Joints.
705.4.2 Threaded Joints.
705.5 PVC and PVC Co-Extruded Plastic Pipe and Joining Methods.
705.5.1 Mechanical Joints.
705.5.2 Solvent Cement Joints.
705.5.3 Threaded Joints.
705.6 Stainless Steel Pipe and Joints.
705.6.1 Mechanical Joints.
705.6.2 Welded Joints.
705.7 Vitrified Clay Pipe and Joints.
705.7.1 Mechanical Joints.
705.8 Special Joints.
705.8.1 Slip Joints.
705.8.2 Expansion Joints. <\/td>\n<\/tr>\n
94<\/td>\n705.8.3 Ground Joint, Flared, or Ferrule Connections.
705.8.4 Transition Joint.
705.9 Joints Between Various Materials.
705.9.1 Copper or Copper Alloy Pipe to Cast-Iron Pipe.
705.9.2 Copper or Copper Alloy Pipe toThreaded Pipe Joints.
705.9.3 Plastic Pipe to Other Materials.
705.9.4 Stainless Steel Pipe to Other Materials.
706.0 Changes in Direction of Drainage Flow.
706.1 Approved Fittings.
706.2 Horizontal to Vertical.
706.3 Horizontal to Horizontal.
706.4 Vertical to Horizontal.
707.0 Cleanouts.
707.1 Plug.
707.2 Approved.
707.3 Watertight and Gastight.
707.4 Location.
Table 707.1 Cleanouts <\/td>\n<\/tr>\n
95<\/td>\n707.5 Cleaning.
707.6 Extension.
707.7 Interceptor.
707.8 Access.
707.9 Clearance.
707.10 Fittings.
707.11 Pressure Drainage Systems.
707.12 Countersunk Cleanout Plugs.
707.13 Hubless Blind Plugs.
707.14 Trap Arms.
708.0 Grade of Horizontal Drainage Piping.
708.1 General.
709.0 Gravity Drainage Required.
709.1 General.
710.0 Drainage of Fixtures Located Below the Next Upstream Manhole or Below the Main Sewer Level.
710.1 Backflow Protection.
710.2 Sewage Discharge.
710.3 Sewage Ejector and Pumps. <\/td>\n<\/tr>\n
96<\/td>\n710.4 Discharge Line.
710.5 Size of Building Drains and Sewers.
710.6 Backwater Valves.
710.7 Drainage and Venting Systems.
710.8 Sump and Receiving Tank Construction.
710.9 Alarm.
710.10 Sump and Receiving Tank Covers and Vents.
710.11 Air Tanks.
710.12 Grinder Pump Ejector.
710.12.1 Discharge Piping.
710.13 Macerating Toilet Systems and Pumped Waste Systems.
710.13.1 Sumps.
710.13.2 Discharge Piping.
710.13.3 Venting. <\/td>\n<\/tr>\n
97<\/td>\n711.0 Suds Relief.
711.1 General.
712.0 Testing.
712.1 Media.
712.2 Water Test.
712.3 Air Test.
Part II \u2013 Building Sewers.
713.0 Sewer Required.
713.1 Where Required.
713.2 Private Sewage Disposal System.
713.3 Public Sewer.
713.4 Public Sewer Availability.
713.5 Permit.
713.6 Lot.
713.7 Installation. <\/td>\n<\/tr>\n
98<\/td>\n714.0 Damage to Public Sewer or Private Sewage Disposal System.
714.1 Unlawful Practices.
714.2 Prohibited Water Discharge.
714.3 Prohibited Sewer Connection.
714.4 Commercial Food Waste Disposer.
714.5 Tanks.
715.0 Building Sewer Materials.
715.1 Materials.
715.2 Joining Methods and Materials.
715.3 Existing Sewers.
716.0 Markings.
716.1 General.
717.0 Size of Building Sewers.
717.1 General.
718.0 Grade, Support, and Protection of Building Sewers.
718.1 Slope.
718.2 Support.
718.3 Protection from Damage.
719.0 Cleanouts.
719.1 Locations.
719.2 No Additional Cleanouts.
719.3 Building Sewer Cleanouts.
719.4 Cleaning.
Table 717.1 Maximum\/Minimum Fixture Unit Loading on Building Sewer Piping <\/td>\n<\/tr>\n
99<\/td>\n719.5 Access.
719.6 Manholes.
720.0 Sewer and Water Pipes.
720.1 General.
721.0 Location.
721.1 Building Sewer.
721.2 Abutting Lot.
722.0 Abandoned Sewers and Sewage Disposal Facilities.
722.1 Building (House) Sewer.
722.2 Cesspools, Septic Tanks, and Seepage Pits.
722.3 Filling.
722.4 Ownership.
722.5 Disposal Facilities.
723.0 Building Sewer Test.
723.1 General.
Table 721.1 Minimum Horizontal Distance Required from Building Sewer (feet) <\/td>\n<\/tr>\n
100<\/td>\nChapter 8 Indirect Wastes
801.0 General.
801.1 Applicability.
801.2 Air Gap or Air Break Required.
801.3 Food and Beverage Handling Establishments.
801.3.1 Size of Indirect Waste Pipes.
801.3.2 Walk-In Coolers.
801.3.3 Food-Handling Fixtures.
801.4 Bar and Fountain Sink Traps.
801.5 Connections from Water Distribution System.
801.6 Sterilizers.
801.7 Drip or Drainage Outlets.
TABLES <\/td>\n<\/tr>\n
101<\/td>\n802.0 Approvals.
802.1 General.
803.0 Indirect Waste Piping.
803.1 Materials.
803.2 Copper and Copper Alloys.
803.3 Pipe Size and Length.
804.0 Indirect Waste Receptors.
804.1 Standpipe Receptors.
805.0 Pressure Drainage Connections.
805.1 General.
806.0 Sterile Equipment.
806.1 General.
807.0 Appliances.
807.1 Non-Classed Apparatus.
807.2 Undiluted Condensate Waste.
807.3 Domestic Dishwashing Machine.
808.0 Cooling Water.
808.1 General.
809.0 Drinking Fountains.
809.1 General.
810.0 Steam and Hot Water Drainage Condensers and Sumps.
810.1 High Temperature Discharge. <\/td>\n<\/tr>\n
102<\/td>\n810.2 Sumps, Condensers, and Intercepting Tanks.
810.3 Cleaning.
810.4 Strainers.
811.0 Chemical Wastes.
811.1 Pretreatment.
811.2 Waste and Vent Pipes.
811.3 Joining Materials.
811.4 Access.
811.5 Permanent Record.
811.6 Chemical Vent.
811.7 Discharge.
811.8 Diluted Chemicals.
812.0 Clear Water Wastes.
812.1 General.
Table 810.1 Pipe Connections in Blowoff Condensers and Sumps <\/td>\n<\/tr>\n
103<\/td>\n813.0 Swimming Pools.
813.1 General.
814.0 Condensate Waste and Control.
814.1 Condensate Disposal.
814.1.1 Condensate Pumps.
814.2 Condensate Control.
814.2.1 Protection of Appurtenances.
814.3 Condensate Waste Pipe Material and Sizing.
814.3.1 Cleanouts.
814.4 Appliance Condensate Drains.
814.5 Point of Discharge.
814.6 Condensate Waste From Air-Conditioning Coils.
814.7 Plastic Fittings.
Table 814.3 Minimum Condensate Pipe Size <\/td>\n<\/tr>\n
104<\/td>\nChapter 9 Vents
901.0 General.
901.1 Applicability.
901.2 Vents Required.
901.3 Trap Seal Protection.
902.0 Vents Not Required.
902.1 Interceptor.
902.2 Bars, Soda Fountains, and Counter.
903.0 Materials.
903.1 Applicable Standards.
903.2 Use of Copper or Copper Alloy Tubing.
903.2.1 Aboveground.
903.2.2 Prohibited Use.
903.2.3 Marking.
903.3 Changes in Direction.
904.0 Size of Vents.
904.1 Size.
904.2 Length.
905.0 Vent Pipe Grades and Connections.
905.1 Grade.
905.2 Horizontal Drainage Pipe.
905.3 Vent Pipe Rise. <\/td>\n<\/tr>\n
105<\/td>\n905.4 Roof Termination.
905.5 Location of Opening.
905.6 Common Vertical Pipe.
906.0 Vent Termination.
906.1 Roof Termination.
906.2 Clearance.
906.3 Use of Roof.
906.4 Outdoor Installations.
906.5 Joints.
906.6 Lead.
906.7 Frost or Snow Closure.
907.0 Vent Stacks and Relief Vents.
907.1 Drainage Stack.
907.2 Yoke Vent.
908.0 Wet Venting.
908.1 Vertical Wet Venting.
908.1.1 Size.
908.1.2 Vent Connection.
908.2 Horizontal Wet Venting for a Bathroom Group.
908.2.1 Vent Connection.
908.2.2 Size. <\/td>\n<\/tr>\n
106<\/td>\n908.2.3 Trap Arm.
908.2.4 Water Closet.
908.2.5 Additional Fixtures.
909.0 Special Venting for Island Fixtures.
909.1 General.
910.0 Combination Waste and Vent Systems.
910.1 Where Permitted.
910.2 Approval.
910.3 Vents.
910.4 Size.
910.5 Vertical Waste Pipe.
910.6 Cleanouts.
910.7 Fixtures.
911.0 Circuit Venting.
911.1 Circuit Vent Permitted. <\/td>\n<\/tr>\n
107<\/td>\n911.1.1 Multiple Circuit-Vented Branches.
911.2 Vent Size and Connection.
911.3 Slope and Size of Horizontal Branch.
911.3.1 Size of Multiple Circuit Vent.
911.4 Relief Vent.
911.4.1 Connection and Installation.
911.4.2 Fixture Drain or Branch.
911.5 Additional Fixtures.
912.0 Engineered Vent System.
912.1 General.
912.2 Minimum Requirements. <\/td>\n<\/tr>\n
108<\/td>\nChapter 10 Traps and Interceptors
1001.0 General.
1001.1 Applicability.
1001.2 Where Required.
1002.0 Traps Protected by Vent Pipes.
1002.1 Vent Pipes.
1002.2 Fixture Traps.
1002.3 Change of Direction.
1002.4 Vent Pipe Opening.
1003.0 Traps \u2014 Described.
1003.1 General Requirements.
1003.2 Slip Joint Fittings.
TABLES
Table 1002.2 Horizontal Lengths of Trap Arms (Except for Water Closets and Similar Fixtures) <\/td>\n<\/tr>\n
109<\/td>\n1003.3 Size.
1004.0 Traps.
1004.1 Prohibited.
1004.2 Movable Parts.
1005.0 Trap Seals.
1005.1 General.
1006.0 Floor Drain Traps.
1006.1 General.
1007.0 Trap Seal Protection.
1007.1 General.
1008.0 Building Traps.
1008.1 General.
1009.0 Interceptors (Clarifiers) and Separators.
1009.1 Where Required.
1009.2 Approval.
1009.3 Design.
1009.4 Relief Vent.
1009.5 Location.
1009.6 Maintenance of Interceptors.
1009.7 Discharge.
1010.0 Slaughterhouses, Packing Establishments, etc.
1010.1 General.
1011.0 Minimum Requirements for Auto Wash Racks.
1011.1 General. <\/td>\n<\/tr>\n
110<\/td>\n1012.0 Commercial and Industrial Laundries.
1012.1 General.
1013.0 Bottling Establishments.
1013.1 General.
1014.0 Grease Interceptors.
1014.1 General.
1014.1.1 Trapped and Vented.
1014.1.2 Maintenance.
1014.1.3 Food Waste Disposers and Dishwashers.
1014.2 Hydromechanical Grease Interceptors.
1014.2.1 Capacity.
1014.2.2 Vent.
1014.3 Gravity Grease Interceptors.
1014.3.1 General.
1014.3.2 Waste Discharge Requirements. <\/td>\n<\/tr>\n
111<\/td>\n1014.3.2.1 Toilets and Urinals.
1014.3.2.2 Inlet Pipe.
1014.3.3 Design.
1014.3.4 Location.
1014.3.4.1 Interceptors.
1014.3.4.2 Business Establishment.
1014.3.4.3 Access.
1014.3.5 Construction Requirements.
1014.3.6 Sizing Criteria.
1014.3.7 Abandoned Gravity Grease Interceptors.
Table 1014.2.1 Hydromechanical Grease Interceptor Sizing Using Gravity Flow Rates <\/td>\n<\/tr>\n
112<\/td>\n1015.0 FOG (Fats, Oils, and Greases) Disposal System.
1015.1 Purpose.
1015.2 Components, Materials, and Equipment.
1015.3 Sizing and Installation.
1015.4 Performance.
1016.0 Sand Interceptors.
1016.1 Discharge.
1016.2 Authority Having Jurisdiction.
1016.3 Construction and Size.
Table 1014.3.6 Gravity Grease Interceptor Sizing <\/td>\n<\/tr>\n
113<\/td>\n1016.4 Separate Use.
1017.0 Oil and Flammable Liquid Interceptors.
1017.1 Interceptors Required.
1017.2 Design of Interceptors. <\/td>\n<\/tr>\n
114<\/td>\nChapter 11 Storm Drainage
1101.0 General.
1101.1 Applicability.
1101.2 Where Required.
1101.3 Storm Water Drainage to Sanitary Sewer Prohibited.
1101.4 Material Uses.
1101.4.1 Copper and Copper Alloys.
1101.4.2 Conductors.
1101.4.3 Leaders.
1101.4.4 Underground Building Storm Drains.
1101.4.5 Building Storm Sewers.
1101.4.6 Subsoil Drains.
1101.5 Expansion Joints Required.
1101.6 Subsoil Drains.
1101.6.1 Discharge.
1101.6.2 Sump.
1101.6.3 Splash Blocks.
1101.6.4 Backwater Valve.
1101.6.5 Open Area.
1101.7 Building Subdrains.
1101.8 Areaway Drains.
1101.9 Window Areaway Drains.
1101.10 Filling Stations and Motor Vehicle Washing Establishments.
1101.11 Paved Areas.
1101.12 Roof Drainage.
1101.12.1 Primary Roof Drainage.
TABLES
Table 1101.4.6 Materials for Subsoil Drain Pipe and Fittings <\/td>\n<\/tr>\n
115<\/td>\n1101.12.2 Secondary Drainage.
1101.12.2.1 Roof Scuppers or Open Side.
1101.12.2.2 Secondary Roof Drain.
1101.12.2.2.1 Separate Piping System.
1101.12.2.2.2 Combined System.
1101.13 Cleanouts.
1101.13.1 Rain Leaders and Conductors.
1101.14 Rainwater Sumps.
1101.15 Traps on Storm Drains and Leaders.
1101.15.1 Where Not Required.
1101.15.2 Trap Size.
1101.15.3 Method of Installation of Combined Sewer.
1101.16 Leaders, Conductors, and Connections.
1101.16.1 Protection of Leaders.
1101.16.2 Combining Storm with Sanitary Drainage.
1102.0 Roof Drains.
1102.1 Applications.
1102.2 Dome Strainers Required.
1102.3 Roof Drain Flashings.
1102.3.1 Lead Flashing.
1102.3.2 Copper Flashing. <\/td>\n<\/tr>\n
116<\/td>\n1103.0 Size of Leaders, Conductors, and Storm Drains.
1103.1 Vertical Conductors and Leaders.
1103.2 Size of Horizontal Storm Drains and Sewers.
1103.3 Size of Roof Gutters.
1103.4 Side Walls Draining onto a Roof.
1104.0 Values for Continuous Flow.
1104.1 General.
1105.0 Controlled-Flow Roof Drainage.
1105.1 Application.
Table 1105.1(1) Controlled-Flow Maximum Roof Water Depth <\/td>\n<\/tr>\n
117<\/td>\n1105.2 Setback Roofs.
1106.0 Testing.
1106.1 Testing Required.
1106.2 Methods of Testing Storm Drainage Systems.
1106.2.1 Water Test.
1106.2.2 Air Test.
1106.2.3 Exceptions.
Table 1105.1(2) Distance of Scupper Bottoms Above Roof <\/td>\n<\/tr>\n
118<\/td>\nTable 1101.8 Sizing of Horizontal Rainwater Piping <\/td>\n<\/tr>\n
119<\/td>\nTable 1101.12 Sizing of Drains, Leaders, and Vertical Rainwater Piping <\/td>\n<\/tr>\n
120<\/td>\nTable 1103.3 Size of Gutters <\/td>\n<\/tr>\n
122<\/td>\nChapter 12 Fuel Gas Piping <\/td>\n<\/tr>\n
124<\/td>\nChapter 13 Health Care Facilities and Medical Gas and Medical Vacuum Systems <\/td>\n<\/tr>\n
126<\/td>\nChapter 14 Firestop Protection <\/td>\n<\/tr>\n
128<\/td>\nChapter 15 Alternate Water Sources for Nonpotable Applications <\/td>\n<\/tr>\n
130<\/td>\nChapter 16 Nonpotable Rainwater Catchment Systems <\/td>\n<\/tr>\n
132<\/td>\nChapter 17 Referenced Standards
1701.0 General.
1701.1 Standards.
TABLE
Table 1701.1 Referenced Standards <\/td>\n<\/tr>\n
155<\/td>\nAbbreviations in Table 1701.1 <\/td>\n<\/tr>\n
156<\/td>\nAppendices Table of Contents <\/td>\n<\/tr>\n
158<\/td>\nAppendix A Recommended Rules for Sizing the Water Supply System
A 101.0 General.
A 101.1 Applicability.
A 102.0 Preliminary Information.
A 102.1 Daily Service Pressure.
A 102.2 Water Meter.
A 102.3 Local Information.
A 103.0 Demand Load.
A 103.1 Supply Demand.
A 103.2 Continuous Supply Demand.
A 104.0 Permissible Friction Loss.
A 104.1 Residual Pressure.
TABLES
CHARTS
Chart A 102.2 Friction Losses for Disk-Type Water Meters <\/td>\n<\/tr>\n
159<\/td>\nA 104.2 Elevation.
A 104.3 Available Pressure.
A 104.4 Developed Length.
A 105.0 Size of Building Supply.
A 105.1 Diameter.
A 105.2 Copper and Copper Alloy Piping.
A 105.3 Hard Water.
A 106.0 Size of Principal Branches and Risers.
A 106.1 Size.
A 106.2 Branches.
A 106.3 Water Closets.
A 107.0 General.
A 107.1 Velocities.
A 107.2 Pressure-Reducing Valves.
A 107.3 Fittings. <\/td>\n<\/tr>\n
160<\/td>\nTable A 103.1 Water Supply Fixture Units (WSFU) and Minimum Fixture Branch Pipe Sizes <\/td>\n<\/tr>\n
161<\/td>\nChart A 103.1(1) Estimate Curves for Demand Load
Chart A 103.1(2) Enlarged Scale Demand Load <\/td>\n<\/tr>\n
162<\/td>\nTable A 104.4 Allowance in Equivalent Length of Pipe for Friction Loss in Valves and Threaded Fittings Equivalent Length of Pipe for Various Fittings <\/td>\n<\/tr>\n
163<\/td>\nChart A 105.1(1) <\/td>\n<\/tr>\n
164<\/td>\nChart A 105.1(2) <\/td>\n<\/tr>\n
165<\/td>\nChart A 105.1(3) <\/td>\n<\/tr>\n
166<\/td>\nChart A 105.1(4) <\/td>\n<\/tr>\n
167<\/td>\nA 108.0 Sizing.
A 108.1 Example.
A 108.1 Example <\/td>\n<\/tr>\n
168<\/td>\nAppendix B Explanatory Notes on Combination Waste and Vent Systems
B 101.0 General.
B 101.1 Applicability.
B 101.2 General Requirements.
B 101.3 Caution.
B 101.4 Pneumatics.
B 101.5 Trap Sizes.
B 101.6 Layout Drawings.
B 101.6.1 Example of Sizing. <\/td>\n<\/tr>\n
170<\/td>\nAppendix C Alternate Plumbing Systems
C 101.0 General.
C 101.1 Applicability.
C 101.2 Provisions.
C 101.3 Authority Having Jurisdiction.
C 101.4 Standards and Specifications.
C 101.5 Alternate Materials and Equipment.
C 201.0 Definitions.
C 201.1 General.
C 301.0 Engineered Plumbing Systems.
C 301.1 Inspection and Installation.
C 301.2 Owner Information.
C 302.0 Water Heat Exchangers.
C 302.1 Protection from Contamination.
C 302.2 Single-Wall Heat Exchangers.
C 302.3 Alternate Designs.
C 303.0 Fixture Unit Values for Private or Private Use Bathroom Groups.
C 303.1 Fixtures.
C 303.2 Water Supply Fixture Unit Values.
C 303.3 Drainage Fixture Unit Values.
TABLES <\/td>\n<\/tr>\n
171<\/td>\nC 304.0 Drainage System Sizing.
C 304.1 Drainage Fixture Units.
C 304.2 Size of Building Drain and Building Sewer.
C 304.3 Size of Horizontal Branch or Vertical Stack.
C 304.3.1 Horizontal Stack Offsets.
C 304.3.2 Vertical Stack Offsets.
C 304.4 Horizontal Stack Offset and Horizontal Branch Connections.
C 401.0 Vent System Sizing.
C 401.1 Size of Vents.
Table C 303.1(1) Water Supply Fixture Units (WSFU) for Bathroom Groups <\/td>\n<\/tr>\n
172<\/td>\nC 401.2 Vent Stack.
C 401.3 Branch Vents.
C 401.4 Venting Horizontal Offsets.
C 401.4.1 Venting Upper Section.
C 401.4.2 Venting Lower Section.
Table C 303.1(2) Drainage Fixture Unit Values (DFU) for Bathroom Groups <\/td>\n<\/tr>\n
173<\/td>\nC 501.0 Vacuum Drainage Systems.
C 501.1 General.
C 501.2 System Design.
Table C 304.2 Building Drains and Building Sewers
Table C 304.3 Horizontal Fixture Branches and Stacks <\/td>\n<\/tr>\n
174<\/td>\nC 501.2.1 Vacuum Generating System.
C 501.2.2 Waste Collection Center or Storage Tanks.
C 501.2.3 Piping Network.
C 501.2.4 Vacuum Interface Valve.
Table C 401.1 Size and Length of Vents <\/td>\n<\/tr>\n
175<\/td>\nC 501.2.5 Control Components.
C 501.3 Fixtures.
C 501.4 Drainage Fixture Units.
C 501.5 Water Supply Fixture Units.
C 501.6 Materials.
C 501.7 Traps and Cleanouts.
C 501.8 Testing.
C 501.9 Manufacturer\u2019s Instructions.
C 601.0 Single-Stack Vent System.
C 601.1 Where Permitted.
Table C 601.2 Singler Stack Size <\/td>\n<\/tr>\n
176<\/td>\nC 601.2 Stack Size.
C 601.2.1 Stack Vent.
C 601.3 Branch Size.
C 601.4 Length of Horizontal Branches.
C 601.4.1 Other Fixtures.
C 601.4.2 Length of Vertical Piping.
C 601.5 Maximum Vertical Drops from Fixtures.
C 601.6 Additional Venting Required.
C 601.7 Stack Offsets.
C 601.8 Separate Stack Required.
C 601.9 Sizing Building Drains and Sewers. <\/td>\n<\/tr>\n
178<\/td>\nAppendix D Sizing Storm Water Drainage Systems
D 101.0 General.
D 101.1 Applicability.
D 102.0 Sizing by Flow Rate.
D 102.1 General.
D 103.0 Sizing by Roof Area.
D 103.1 General.
D 104.0 Capacity of Rectangular Scuppers.
D 104.1 General.
TABLES
Table D 101.1 Maximum Rates of Rainfall for Various Cities <\/td>\n<\/tr>\n
184<\/td>\nTable D 104.1 Discharge from Rectangular Scuppers (gallons per minute) <\/td>\n<\/tr>\n
186<\/td>\nAppendix E Manufactured\/Mobile Home Parks and Recreational Vehicle Parks
E 101.0 Manufactured\/Mobile Home (M\/H) Park.
E 101.1 Applicability.
E 101.2 Definitions.
E 102.0 Construction Documents.
E 102.1 General Requirements.
E 201.0 Manufactured\/Mobile Home Park Drainage System Construction.
E 201.1 Drainage Systems.
E 202.0 Materials.
E 202.1 General.
E 203.0 Drainage (Sewage) Lines.
E 203.1 General.
E 204.0 M\/H Lot Drainage Inlet and Lateral.
E 204.1 Size.
TABLES <\/td>\n<\/tr>\n
187<\/td>\nE 204.2 Lateral Line.
E 204.3 Materials.
E 204.4 Inlet.
E 205.0 Location of Lot Drain Inlet.
E 205.1 General.
E 206.0 Pipe Size.
E 206.1 Inlet, System, and Lateral Sizing.
E 206.2 Engineered Design.
E 207.0 M\/H Drain Connector.
E 207.1 General.
E 207.2 Grade and Gastightness.
E 301.0 M\/H Park Water Supply.
E 301.1 Potable Water Supply.
E 302.0 Lot Service Outlet Size.
E 302.1 General.
E 303.0 Location of Water Service.
E 303.1 General.
E 304.0 Pressure.
E 304.1 General.
Table E 203.1(1) Drainage Pipe Diameter and Number of Fixture Units on Drainage System
Table 203.1(2) Minimum Grade and Slope of Drainage Pipe <\/td>\n<\/tr>\n
188<\/td>\nE 305.0 Water Distribution Piping.
E 305.1 General.
E 306.0 Shutoff Valve.
E 306.1 General.
E 307.0 Backflow Preventer.
E 307.1 General.
E 308.0 Pressure-Relief Valve.
E 308.1 General.
E 309.0 Mechanical Protection.
E 309.1 General.
E 310.0 M\/H Water Connector.
E 310.1 General.
E 311.0 Water-Conditioning Equipment.
E 311.1 Permit Required.
E 311.2 Approval.
E 311.3 Installation.
E 312.0 Testing.
E 312.1 General.
E 401.0 Fuel Supply.
E 401.1 Fuel Gas Piping Systems.
E 401.2 Gas Supply Connections.
E 401.3 Location of Gas Supply Connection.
E 401.4 Recreational Vehicle Park Fuel Gas Equipment and Installations.
E 402.0 Single and Multiple Manufactured Home Site Fuel Supply Systems.
E 402.1 Underground Installations.
E 402.1.1 Open-Ended Gastight Conduit.
E 402.1.2 Requirements.
E 403.0 Manufactured Home Site Gas Shutoff Valve.
E 403.1 General.
E 404.0 Gas Meters.
E 404.1 Support of Meters.
E 404.2 Location of Meters.
E 404.3 Meter Shutoff Valve or Cock.
E 405.0 Cathodic Protection Requirements.
E 405.1 General.
E 406.0 Manufactured Home Community LP-Gas Supply Systems.
E 406.1 General.
E 407.0 Required Gas Supply.
E 407.1 General. <\/td>\n<\/tr>\n
189<\/td>\nE 408.0 Gas Pipe Sizing and Pressure.
E 408.1 Size.
E 408.2 Pressure.
E 409.0 Gas Piping Materials.
E 409.1 Metal.
E 409.2 Protection Coatings for Metal Gas Piping.
E 409.3 Plastic.
E 410.0 Gas Piping Installations.
E 410.1 Minimum Burial Below Ground Level and Clearances.
E 410.2 Metallic Gas Piping.
E 410.2.1 Cathodic Protection.
E 410.2.2 Underground Metallic Systems.
E 410.3 Plastic Gas Piping.
E 410.4 Gas Piping System Shutoff Valve.
E 411.0 Liquefied Petroleum Gas Equipment.
E 411.1 General.
E 412.0 Oil Supply.
E 412.1 General.
E 412.2 Minimum Oil Supply Tank Size.
E 412.3 Oil Supply Connections.
E 413.0 Fuel Supply Systems Installation.
E 413.1 Flexible Gas Connector.
E 413.2 Use of Approved Pipe and Fittings of Extension.
E 413.3 Mechanical Protection.
E 413.4 Special Rules on Atmospherically Controlled Regulators.
E 413.5 Fuel Gas Piping Test.
E 413.5.1 Procedures.
E 413.5.2 Warning.
E 413.5.3 Vents.
E 413.6 Oil Tanks.
E 413.6.1 Installation.
E 413.6.2 Capacity.
E 413.6.3 Location.
E 413.6.4 Vent.
E 413.6.5 Liquid Level.
E 413.6.6 Fill Opening.
E 414.0 Manufactured Home Accessory Building Fuel Supply Systems.
E 414.1 General.
E 415.0 Community Building Fuel Supply Systems in Manufactured Home Communities.
E 415.1 Fuel Gas Piping and Equipment Installations.
E 415.2 Oil Supply Systems in M\/H Communities.
E 415.3 Oil-Burning Equipment and Installation.
E 415.4 Inspections and Tests.
E 501.0 Recreational Vehicle Parks.
E 501.1 Plumbing Systems.
E 601.0 Recreational Vehicle Park Toilet and Shower Facilities.
E 601.1 Water Closets and Urinals.
E 602.0 Markings.
E 602.1 General.
E 603.0 Number of Water Closets.
E 603.1 General.
E 604.0 Interior Finish.
E 604.1 General.
E 605.0 Floors and Drains.
E 605.1 General.
Table E 407.1 Demand Factors for Use in Calculating Gas Piping Systems in M\/H Communities <\/td>\n<\/tr>\n
190<\/td>\nE 606.0 Lavatories.
E 606.1 General.
E 607.0 Urinals.
E 607.1 General.
E 608.0 Approved Water Closets.
E 608.1 General.
E 609.0 Water Closet Compartment.
E 609.1 General.
E 610.0 Compartment Size.
E 610.1 General.
E 611.0 Receptacle.
E 611.1 General.
E 612.0 Shower Size.
E 612.1 General.
E 613.0 Drainage System Connection.
E 613.1 General.
E 614.0 Ceiling Height and Doors.
E 614.1 General.
E 615.0 Ventilation.
E 615.1 General.
E 701.0 Recreational Vehicle Park Potable Water Supply and Distribution.
E 701.1 Quality.
E 702.0 Sources.
E 702.1 General.
E 703.0 Prohibited Connections.
E 703.1 General. <\/td>\n<\/tr>\n
191<\/td>\nE 704.0 Supply.
E 704.1 General.
E 705.0 Pressure and Volume.
E 705.1 General.
E 706.0 Outlets.
E 706.1 General.
E 707.0 Storage Tanks.
E 707.1 General.
E 801.0 Recreational Vehicle Park Water Connections for Individual Recreational Vehicles.
E 801.1 Location.
E 802.0 Water Riser Pipe.
E 802.1 General.
E 803.0 Drinking Fountains.
E 803.1 General.
E 901.0 Recreational Vehicle Park Drainage System.
E 901.1 Where Required.
E 902.0 Materials.
E 902.1 General.
E 903.0 Pipe Sizes.
E 903.1 General.
E 904.0 Sewer Lines.
E 904.1 General.
E 905.0 Cleanouts.
E 905.1 General.
E 1001.0 Recreational Vehicle Site Drainage System Inlet.
E 1001.1 Sewer Riser Pipe.
Table E 903.1 Pipe Sizes <\/td>\n<\/tr>\n
192<\/td>\nE 1002.0 Location.
E 1002.1 General.
E 1003.0 Protection.
E 1003.1 General.
E 1101.0 Recreational Vehicle Park Sanitary Disposal Stations.
E 1101.1 Where Required.
E 1102.0 Access.
E 1102.1 General.
E 1103.0 Construction.
E 1103.1 General.
E 1104.0 Flushing Device.
E 1104.1 General.
E 1201.0 Recreational Vehicle Park Water Supply Stations.
E 1201.1 Potable Watering Stations. <\/td>\n<\/tr>\n
194<\/td>\nAppendix F Firefighter Breathing Air Replenishment Systems <\/td>\n<\/tr>\n
196<\/td>\nAppendix G Sizing of Venting Systems <\/td>\n<\/tr>\n
198<\/td>\nAppendix H Private Sewage Disposal Systems <\/td>\n<\/tr>\n
200<\/td>\nAppendix I Installation Standard for PEX Tubing Systems for Hot- and Cold-Water Distribution
1.0 Scope.
1.1 General.
1.1.1 This Standard specifies requirements for the installation of SDR 9 CTS crosslinked polyethylene (PEX) tubing and fittings, including cold-expansion, crimp, press, and mechanical compression fittings, intended for hot- and cold-water distribution systems within buildings.
1.1.2 This Standards applies to (a) SDR 9 CTS PEX tubing complying with ASTM F876 and pressure-rated in accordance with PPI TR-3; and (b) PEX fitting systems complying with (i) ASTM F877, for mechanical compression fittings and metal or plastic insert fittings with stainless steel press sleeves; (ii) ASTM F1807 or ASTM F2159, for metal or plastic insert fittings with copper crimp rings; (iii) ASTM F1960, for cold expansion fittings with PEX reinforced rings; or (iv) ASTM F2080, for cold expansion fittings with metal compression sleeves.
1.2 Terminology.
1.3 Amendments.
2.0 Reference Publications.
TABLES
FIGURES <\/td>\n<\/tr>\n
201<\/td>\n3.0 Abbreviations.
4.0 General.
4.1 Tubing.
4.1.1 PEX tubing can be (a) pigmented throughout (i.e., with color); (b) non-pigmented (e.g., translucent ornatural); or (c) coated with a pigmented layer.
4.1.2 PEX tubing is typically available in NTS-1\/4 to NTS-3.
4.1.3 Before installation, the installer shall review the tubing markings and verify that (a) the standard designation(s) of the fittings to which the tube can be joined to is included in the markings; (b) it bears a certification mark from an accredited certification organization; and (c) pressure and temperature ratings meet or exceed that of the intended end-use.
4.2 Fittings.
4.2.1 Cold-Expansion Fittings.
4.2.2 Crimp or Press Insert Fittings.
4.2.3 Compression Fittings.
4.3 Installation.
4.4 Tools.
4.5 Tubing Protection.
4.5.1 Abrasion.
4.5.2 Puncture.
5.0 Handling.
5.1 Receiving. <\/td>\n<\/tr>\n
202<\/td>\n5.2 Storage and UV Exposure.
5.2.1 PEX tubing and fittings shall be stored indoors and in its original packaging until the time of installation.
5.2.2 Accumulative exposure time to UV radiation during storage and installation shall not exceed the UV exposure limits recommended by the manufacturer or specified in ASTM F876.
5.3 Exposure to Heat.
5.3.1 PEX tubing and fittings shall not be exposed to open flames.
5.3.2 PEX tubing shall not be exposed to temperatures exceeding 93\u00baC (200\u00baF).
5.4 Exposure to Chemicals.
5.4.1 Chemical compatibility (e.g., with common construction materials) shall be verified with the manufacturer prior to direct contact.
5.4.2 In general, petroleum- or solvent-based chemicals (e.g., paints, greases, pesticides, or sealants) shall not be allowed to come indirect contact with PEX tubing or fittings.
6.0 Thermal Expansion and Contraction.
6.1 Horizontal Tubing Runs.
6.2 Vertical Tubing Runs.
6.3 Clearance.
6.4 Expansion Arms and Expansion Loops.
6.4.1 Expansion Arms (See Figure 1).
6.4.1.1 Expansion arms shall be installed as illustrated in Figure 1.
6.4.1.2 The minimum length of expansion arms shall be calculated using the following equation: LB = C \u00d7 \u221a(D \u00d7 \u0394L) <\/td>\n<\/tr>\n
203<\/td>\n6.4.2 Expansion Loops (See Figure 2).
6.4.2.1 Expansion loops shall be installed at the midpoint between anchors, as illustrated in Figure 2.
6.4.2.2 The minimum length of expansion loops shall be calculated using the equation in Section 6.4.1.2; however, the distance LB shall be divided into three sections, as illustrated in Figure 2, where L1 = LB \u00f7 5; and L2 = L1 \u00d7 2
7.0 Hangers and Supports.
7.1 Vertical Tubing.
7.2 Horizontal Tubing.
7.3 Anchors.
8.0 Joints and Connections.
8.1 Assembly Procedure.
8.2 Concealed Joints.
9.0 Clearances.
9.1 Gas Vents.
9.2 Recessed Light Fixtures.
9.3 Fluorescent Lighting.
10.0 Other Considerations.
10.1 Hot-Work Joints.
10.2 Bending Radius.
10.2.1 The free (unsupported) bending radius for PEX tubing, measured at the outside of the bend, shall be not less than six times the actual outside diameter of the tubing, unless otherwise specified by the PEX manufacturer. <\/td>\n<\/tr>\n
204<\/td>\n10.2.2 Tighter bends may be used when the PEX tubing is uniformly bent (supported) around a curved bracket or other rigid fixture.
10.3 Directional Fittings.
10.4 Direct Burial.
10.5 Fire-Resistive Construction.
10.6 Sizing and Flow Velocities.
10.6.1 PEX tubing shall be sized in accordance with IAPMO\/ANSI UPC 1.
10.6.2 The tubing manufacturer\u2019s pressure-loss data should be referenced when using Appendix A of IAPMO\/ANSI UPC 1.
10.6.3 Flow velocities through the water distribution system, used for calculating flush tank and flush valve fixture units depending on the tubing sizes (see Table 1), shall not exceed (a) 3.0 m\/s (10 ft\/s) for cold-water distribution systems; and (b) 2.4 m\/s (8 ft\/s) for hot-water distribution systems.
10.6.4 Hot-water recirculation systems shall (a) be balanced to maintain adequate system temperatures; and (b) have flow velocities that do not exceed 0.6 m\/s (2 ft\/s) (see Table 2); and (c) use only PEX tubing designated for hot, chlorinated water recirculation systems and rated for the maximum percentage of time during which the system is intended to be operated at elevated temperatures, in accordance with ASTM F876.
10.7 Installation Testing.
Figure 1 Expansion Arms <\/td>\n<\/tr>\n
205<\/td>\nTable 1 Calculation of Flush Tank and Flush Valve Fixture Units
Table 2 Tubing Sizes, Flows, and Friction Losses for Hot-Water Recirculation Systems
Figure 2 Expansion LoopsEXPANSION LOOPS <\/td>\n<\/tr>\n
206<\/td>\nFigure 3 Pressure Los of PEX Tubing at 16 \u00baC (60\u00baF) <\/td>\n<\/tr>\n
207<\/td>\nFigure 4 Pressure Loss of PEX Tubing at 49 \u00baC (120\u00baF) <\/td>\n<\/tr>\n
208<\/td>\nAppendix J Combination of Indoor and Outdoor Combustion and Ventilation Opening Design <\/td>\n<\/tr>\n
210<\/td>\nAppendix K Potable Rainwater Catchment Systems <\/td>\n<\/tr>\n
212<\/td>\nAppendix L Sustainable Practices <\/td>\n<\/tr>\n
214<\/td>\nIndex <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":"

South Dakota Plumbing Code<\/b><\/p>\n\n\n\n\n
Published By<\/td>\nPublication Date<\/td>\nNumber of Pages<\/td>\n<\/tr>\n
SD<\/b><\/a><\/td>\n2015<\/td>\n233<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n","protected":false},"featured_media":165998,"template":"","meta":{"rank_math_lock_modified_date":false,"ep_exclude_from_search":false},"product_cat":[2793],"product_tag":[],"class_list":{"0":"post-165992","1":"product","2":"type-product","3":"status-publish","4":"has-post-thumbnail","6":"product_cat-sd","8":"first","9":"instock","10":"sold-individually","11":"shipping-taxable","12":"purchasable","13":"product-type-simple"},"_links":{"self":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product\/165992","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product"}],"about":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/types\/product"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/media\/165998"}],"wp:attachment":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/media?parent=165992"}],"wp:term":[{"taxonomy":"product_cat","embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product_cat?post=165992"},{"taxonomy":"product_tag","embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product_tag?post=165992"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}