BS ISO 13012-1:2018
$167.15
Rolling bearings. Accessories for sleeve type linear ball bearings – Boundary dimensions, geometrical product specifications (GPS) and tolerances for series 1 and 3
| Published By | Publication Date | Number of Pages |
| BSI | 2018 | 36 |
This document specifies the boundary dimensions, other relevant dimensions and the corresponding tolerances of accessories for sleeve type linear ball bearings which are specified in ISO 10285.
This document applies to:
-
the following housings:
-
closed and adjustable flangeless housings for series 1 sleeve type linear ball bearings,
-
closed and adjustable flanged housings for series 3 sleeve type linear ball bearings,
-
open flanged housings for series 3 sleeve type linear ball bearings,
-
closed and adjustable flangeless housings for series 3 sleeve type linear ball bearings,
-
open and open adjustable flangeless housings for series 3 sleeve type linear ball bearings;
-
-
the following shaft support rails:
-
standard height shaft support rails for series 3 sleeve type linear ball bearings,
-
low height shaft support rails for series 3 sleeve type linear ball bearings;
-
-
the following shaft support blocks:
-
flanged shaft support blocks for series 1 and 3 sleeve type linear ball bearings,
-
flangeless shaft support blocks for series 1 and 3 sleeve type linear ball bearings;
-
-
solid and tubular shafts for series 1 and 3 sleeve type linear ball bearings.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 2 | National foreword |
| 6 | Foreword |
| 7 | Introduction |
| 9 | 1 Scope 2 Normative references |
| 10 | 3 Terms and definitions |
| 11 | 4 Symbols 4.1 General 4.2 Closed and adjustable flangeless housings for series 1 sleeve type linear ball bearings 4.3 Closed and adjustable flanged housings for series 3 sleeve type linear ball bearings |
| 12 | 4.4 Open flanged housings for series 3 sleeve type linear ball bearings 4.5 Closed and adjustable flangeless housings for series 3 sleeve type linear ball bearings |
| 13 | 4.6 Open and open adjustable flangeless housings for series 3 sleeve type linear ball bearings |
| 14 | 4.7 Standard height shaft support rails for series 3 sleeve type linear ball bearings 4.8 Low height shaft support rails for series 3 sleeve type linear ball bearings |
| 15 | 4.9 Flanged shaft support blocks for series 1 and 3 sleeve type linear ball bearings 4.10 Flangeless shaft support blocks for series 1 and 3 sleeve type linear ball bearings |
| 16 | 4.11 Solid and tubular shafts for series 1 and 3 sleeve type linear ball bearings 5 Housings 5.1 General 5.2 Housings for series 1 sleeve type linear ball bearings |
| 17 | 5.3 Housings for series 3 sleeve type linear ball bearings 6 Shaft support rails 7 Shaft support blocks 8 Shafts 8.1 Material 8.2 Heat treatment 8.2.1 Surface hardened shafts 8.2.2 Through hardened shafts |
| 18 | 8.3 Geometrical tolerances 8.3.1 Tolerance classes 8.3.2 Geometric form 8.3.3 Shaft length tolerances 8.3.4 Chamfers 8.3.5 Surface roughness 9 Boundary dimensions and tolerances 9.1 Housings |
| 26 | 9.2 Shaft support rails |
| 29 | 9.3 Shaft support blocks |
| 31 | 9.4 Shafts |
| 34 | Bibliography |
Related products
-
BS ISO 13012-1:2018 – TC:2020 Edition
Tracked Changes. Rolling bearings. Accessories for sleeve type linear ball bearings – Boundary dimensions, geometrical…
