ASTM-D6923 2010(Redline)

This is an accelerated engine oil test, performed in a standardized, calibrated, stationary single-cylinder diesel engine that gives a measure of ( 1 ) piston and ring groove deposit forming tendency, ( 2 ) piston, ring, and liner scuffing and ( 3 ) oil consumption. The test is used in the establishment of diesel engine oil specification requirements as cited in Specification D4485 for appropriate API Performance Category C oils (API 1509). The test method can also be used in diesel engine oil development.

1. Scope

1.1 This test method covers stressing an engine oil under modern high-speed diesel operating conditions and measures the oil’s deposit control, lubrication ability, and resistance to oil consumption. It is performed in a laboratory using a standardized high-speed, single-cylinder diesel engine.

1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.2.1 Exceptions — Where there is no direct SI equivalent such as screw threads, national pipe threads/diameters, and tubing size, or where a sole source supplier is specified.

1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use. Being an engine test method, this test method does have definite hazards that require safe practices (see Appendix X2 on Safety).

2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM Standards

D86 Test Method for Distillation of Petroleum Products at Atmospheric Pressure D93 Test Methods for Flash Point by Pensky-Martens Closed Cup Tester D97 Test Method for Pour Point of Petroleum Products D130 Test Method for Corrosiveness to Copper from Petroleum Products by Copper Strip Test D235 Specification for Mineral Spirits (Petroleum Spirits) (Hydrocarbon Dry Cleaning Solvent) D445 Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity) D524 Test Method for Ramsbottom Carbon Residue of Petroleum Products D613 Test Method for Cetane Number of Diesel Fuel Oil D664 Test Method for Acid Number of Petroleum Products by Potentiometric Titration D976 Test Method for Calculated Cetane Index of Distillate Fuels D1298 Test Method for Density, Relative Density (Specific Gravity), or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method D1319 Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption D2500 Test Method for Cloud Point of Petroleum Products D2622 Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry D2709 Test Method for Water and Sediment in Middle Distillate Fuels by Centrifuge D3338 Test Method for Estimation of Net Heat of Combustion of Aviation Fuels D3524 Test Method for Diesel Fuel Diluent in Used Diesel Engine Oils by Gas Chromatography D4052 Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter D4175 Terminology Relating to Petroleum, Petroleum Products, and Lubricants D4485 Specification for Performance of Active API Service Category Engine Oils D4739 Test Method for Base Number Determination by Potentiometric Hydrochloric Acid Titration D4863 Test Method for Determination of Lubricity of Two-Stroke-Cycle Gasoline Engine Lubricants D5185 Test Method for Determination of Additive Elements, Wear Metals, and Contaminants in Used Lubricating Oils and Determination of Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES) D5302 Test Method for Evaluation of Automotive Engine Oils for Inhibition of Deposit Formation and Wear in a Spark-Ignition Internal Combustion Engine Fueled with Gasoline and Operated Under Low-Temperature, Light-Duty Conditions D5844 Test Method for Evaluation of Automotive Engine Oils for Inhibition of Rusting (Sequence IID) D5862 Test Method for Evaluation of Engine Oils in Two-Stroke Cycle Turbo-Supercharged 6V92TA Diesel Engine D5966 Test Method for Evaluation of Engine Oils for Roller Follower Wear in Light-Duty Diesel Engine D5967 Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine D6202 Test Method for Automotive Engine Oils on the Fuel Economy of Passenger Cars and Light-Duty Trucks in the Sequence VIA Spark Ignition Engine D6594 Test Method for Evaluation of Corrosiveness of Diesel Engine Oil at 135C D6681 Test Method for Evaluation of Engine Oils in a High Speed, Single-Cylinder Diesel Engine–Caterpillar 1P Test Procedure E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications E344 Terminology Relating to Thermometry and Hydrometry G40 Terminology Relating to Wear and Erosion

Coordinating Research Council

CRCManual No. 20 Available from the Coordinating Research Council Inc., 3650 Mansell Road Suite 140, Atlanta, GA 30022-8246.

SAE Standard

SAEJ183 Engine Oil Performance and Engine Service Classification Available from Society of Automotive Engineers (SAE), 400 Commonwealth Dr., Warrendale, PA 15096-0001.

Keywords

Caterpillar 1R test procedure; oil consumption; piston deposits; single cylinder diesel oil test; Caterpillar 1P test procedure; Cooling system arrangement; Fuel heat exhanger; Instrumental measurement–petroleum products; Intake air mass flow sensor installation; Oil consumption; Oil scale measurement; Piston deposits; Pressure testing–petroleum products; Quality index (QI) calculation; Single-cylinder diesel engine ;

ICS Code

ICS Number Code 75.100 (Lubricants, industrial oils and related products)

DOI: 10.1520/D6923-10A ASTM International is a member of CrossRef.

Citing ASTM Standards

[Back to Top]