ASTM-D6875 2008(Redline)

$23.40

D6875-08 Standard Test Method for Solidification Point of Industrial Organic Chemicals by Thermistor (Redline)

Published By	Publication Date	Number of Pages
ASTM	2008	4

Guaranteed Safe Checkout

Categories: 71.080.01 - Organic chemicals in general, ASTM

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

Description

Significance and Use

This test method may be used for process control during the manufacture of organic chemicals described in Section 1, for setting specifications, for development and research work, and to determine if contamination was introduced during shipment.

1. Scope

1.1 This test method covers a general procedure for determining the solidification point of most organic chemicals having appreciable heats of fusion and solidification points between 4 and 41 ° C.

Note 1—Other test methods for determining freeze point and solidification point of aromatic hydrocarbons include Test Methods D 852, D 1015, D 1016, D 3799, D 4493, and D 6269.

1.2 This test method is applicable to relatively pure compounds only. Solidification point depression is dependent on impurity concentrations.

1.3 The following applies to all specified limits in this test method: for purposes of determining conformance with applicable specifications using this test method, an observed value or a calculated value shall be rounded off “ to the nearest unit ” in the last right hand digit used in expressing the specification limit, in accordance with the “ rounding-off method ” of Practice E 29.

1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For a specific hazard statement, see Section 8, Hazards.

2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM Standards

D852 Test Method for Solidification Point of Benzene D1015 Test Method for Freezing Points of High-Purity Hydrocarbons D1016 Test Method for Purity of Hydrocarbons from Freezing Points D3437 Practice for Sampling and Handling Liquid Cyclic Products D3438 Practice for Sampling and Handling Naphthalene, Maleic Anhydride, and Phthalic Anhydride D3799D3852 Practice for Sampling and Handling Phenol, Cresols, and Cresylic Acid D4297 Practice for Sampling and Handling Bisphenol A (4,4 -Isopropylidinediphenol) D4493 Test Method for Solidification Point of Bisphenol A (4,4`-Isopropylidenediphenol) D6269 Test Method for Solidification Point of p-Xylene E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications

Keywords

benzene; cyclohexane; p-Xylene; solidification point; Benzene–paints/related coatings/materials; Contamination–paints/coatings applications; Cyclohexane; Organic chemicals; Process control; Solidification point; para -Xylene;

ICS Code

ICS Number Code 71.080.01 (Organic chemicals in general)

DOI: 10.1520/D6875-08 ASTM International is a member of CrossRef.

ASTM D6875 (Paint and Related Coating Standards)

Citing ASTM Standards

[Back to Top]

Additional information

Standard Title	D6875-08 Standard Test Method for Solidification Point of Industrial Organic Chemicals by Thermistor (Redline)
Published Code	ASTM
Publication Date	2008
Pages Count	4
ICS Codes	71.080.01 - Organic chemicals in general

Preview PDF


PDF Format	Searchable	Printable	Preview Now

ASTM-D6875 2008(Redline)

ASTM D6875 (Paint and Related Coating Standards)

Related products